/** * @defgroup boards_e180-zg120b-tb Ebyte E180-ZG120B-TB Test Board * @ingroup boards * @brief Support for Ebyte E180-ZG120B-TB Test Board ## Overview ![Image of the E180-ZG120B test board](https://www.ebyte.com/Uploadfiles/Picture/2019-12-20/201912201352132348.jpg) Ebyte E180-ZG120B Test Board is equipped with the EFM32 microcontroller. It is specifically designed for low-power applications, having energy-saving peripherals, different energy modes and short wake-up times. ## Hardware ### MCU | MCU | EFR32MG1B232F256GM32 | |---------------|-----------------------------------------------------------------------------------------| | Family | ARM Cortex-M4F | | Vendor | Ebyte | | Vendor Family | EFM32 Mighty Gecko 1B | | RAM | 32.0 KiB (1.0 KiB reserved by radio blob) | | Flash | 256.0 KiB | | EEPROM | no | | Frequency | up to 38.4 MHz | | FPU | yes | | MPU | yes | | DMA | 8 channels | | Timers | 2x 16-bit + 1x 16-bit (low power) | | ADCs | 12-bit ADC | | UARTs | 2x USART, 1x LEUART | | SPIs | 2x USART | | I2Cs | 1x | | Vcc | 1.85 V - 3.8 V | | Datasheet | [Datasheet](https://www.silabs.com/documents/public/data-sheets/efr32mg1-datasheet.pdf) | | Manual | [Manual](https://www.silabs.com/documents/public/reference-manuals/efr32xg1-rm.pdf) | | Board Manual | [Board Manual](http://www.ebyte.com/en/downpdf.aspx?id=896) | ### Pin Mapping @warning At least for revision `10199-V1.0` of the test board most of the silkscreen labels are incorrect. @note Everything here assumes the board is oriented so that the USB connector is on the top. #### Right Header (Top-left pin is 1, top-right pin is 2, and so on.) | Description | Pin (left) | Pin (right) | Description | |:----------------------------- |:------------- |:------------- |:--------------------------------- | | GND | 1 | 2 | VCC | | PB13 | 3 | 4 | PB12 | | PB11 | 5 | 6 | PD15 | | NC (pin 8 on E180-ZG120B) | 7 | 8 | NC (pin 7 on E180-ZG120B) | | PA1 | 9 | 10 | PA0 | | PD14 | 11 | 12 | PD13 | | GND | 13 | 14 | GND | #### Top Header (Leftmost pin is 1, second from left is 2, and so on.) | Description | Pin (left to right) | |:----------------------------- |:--------------------- | | NC (pin 23 on E180-ZG120B) | 1 | | NC (pin 22 on E180-ZG120B) | 2 | | PC11 | 3 | | NC (pin 20 on E180-ZG120B) | 4 | | PF2 | 5 | | PC10 | 6 | | NC (pin 17 on E180-ZG120B) | 7 | | NC (pin 16 on E180-ZG120B) | 8 | | NC (pin 16 on E180-ZG120B) | 9 | #### Left Header (Top-left pin is 1, top-right pin is 2, and so on.) | Description | Pin (left) | Pin (right) | Description | |:----------------------------- |:------------- |:------------- |:----------------------------- | | NC (pin 24 on E180-ZG120B) | 1 | 2 | SWCLK | | SWDIO | 3 | 4 | PB14 | | PB15 | 5 | 6 | NC (pin 29 on E180-ZG120B) | | PF3 | 7 | 8 | NC (pin 31 on E180-ZG120B) | | NC (pin 32 on E180-ZG120) | 9 | 10 | NC (pin 33 on E180-ZG120B) | | NC (pin 34 on E180-ZG120) | 11 | 12 | NC (pin 35 on E180-ZG120B) | | GND | 13 | 14 | Reset | ### Peripheral mapping | Peripheral | Number | Hardware | Pins | Comments | |------------|---------|-----------------|-----------------------------|-----------------------------------------------------| | ADC | 0 | ADC0 | CHAN0: internal temperature | Ports are fixed, 14/16-bit resolution not supported | | HWCRYPTO | — | — | | AES128/AES256, SHA1, SHA256 | | RTT | — | RTCC | | 1 Hz interval. Either RTT or RTC (see below) | | RTC | — | RTCC | | 1 Hz interval. Either RTC or RTT (see below) | | Timer | 0 | TIMER0 + TIMER1 | | TIMER0 is used as prescaler (must be adjacent) | | | 1 | LETIMER0 | | | | UART | 0 | USART0 | RX: PA1, TX: PA0 | Default STDIO output | ### User interface | Peripheral | Mapped to | Pin | Comments | |------------|-----------|------|-----------------| | Button | PB0_PIN | PD15 | Mode Change | | | PB1_PIN | PD13 | Touch Link | | | PB2_PIN | PB11 | Baud Rate Reset | | LED | LED0_PIN | PF2 | GPIO2 LED | | | LED1_PIN | PF3 | Link LED | The fourth button with the Chinese description is the reset button. ## Implementation Status | Device | ID | Supported | Comments | |------------------|-----------|-----------|----------------------------------------------------------------| | MCU | EFR32MG1B | yes | Power modes supported | | Low-level driver | ADC | yes | | | | Flash | yes | | | | GPIO | yes | Interrupts are shared across pins (see reference manual) | | | HW Crypto | yes | | | | I2C | yes | | | | PWM | yes | | | | RTCC | yes | As RTT or RTC | | | SPI | partially | Only master mode | | | Timer | yes | | | | UART | yes | USART is shared with SPI. LEUART baud rate limited (see below) | | | USB | no | | ## Board configuration ### Clock selection There are several clock sources that are available for the different peripherals. You are advised to read [AN0004.0](https://www.silabs.com/documents/public/application-notes/an0004.0-efm32-cmu.pdf) to get familiar with the different clocks. | Source | Internal | Speed | Comments | |--------|----------|----------------------------------|------------------------------------| | HFRCO | Yes | 19 MHz | Enabled during startup, changeable | | HFXO | No | 38.4 MHz | | | LFRCO | Yes | 32.768 kHz | | | LFXO | No | 32.768 kHz | | | ULFRCO | No | 1 kHz | Not very reliable as a time source | The sources can be used to clock following branches: | Branch | Sources | Comments | |--------|-------------------------|------------------------------| | HF | HFRCO, HFXO | Core, peripherals | | LFA | LFRCO, LFXO | Low-power timers | | LFB | LFRCO, LFXO, CORELEDIV2 | Low-power UART | | LFE | LFRCO, LFXO | Real-time Clock and Calendar | CORELEDIV2 is a source that depends on the clock source that powers the core. It is divided by 2 or 4 to not exceed maximum clock frequencies (EMLIB takes care of this). The frequencies mentioned in the tables above are specific for this starter kit. It is important that the clock speeds are known to the code, for proper calculations of speeds and baud rates. If the HFXO or LFXO are different from the speeds above, ensure to pass `EFM32_HFXO_FREQ=freq_in_hz` and `EFM32_LFXO_FREQ=freq_in_hz` to your compiler. You can override the branch's clock source by adding `CLOCK_LFA=source` to your compiler defines, e.g. `CLOCK_LFA=cmuSelect_LFRCO`. ### Low-power peripherals The low-power UART is capable of providing an UART peripheral using a low-speed clock. When the LFB clock source is the LFRCO or LFXO, it can still be used in EM2. However, this limits the baud rate to 9600 baud. If a higher baud rate is desired, set the clock source to CORELEDIV2. **Note:** peripheral mappings in your board definitions will not be affected by this setting. Ensure you do not refer to any low-power peripherals. ### RTC or RTT RIOT-OS has support for *Real-Time Tickers* and *Real-Time Clocks*. However, this board MCU family has support for a 32-bit *Real-Time Clock and Calendar*, which can be configured in ticker mode **or** calendar mode. Therefore, only one of both peripherals can be enabled at the same time. Configured at 1 Hz interval, the RTCC will overflow each 136 years. ### Hardware crypto This MCU is equipped with a hardware-accelerated crypto peripheral that can speed up AES128, AES256, SHA1, SHA256 and several other cryptographic computations. A peripheral driver interface is proposed, but not yet implemented. ### Usage of EMLIB This port makes uses of EMLIB by Ebyte to abstract peripheral registers. While some overhead is to be expected, it ensures proper setup of devices, provides chip errata and simplifies development. The exact overhead depends on the application and peripheral usage, but the largest overhead is expected during peripheral setup. A lot of read/write/get/set methods are implemented as inline methods or macros (which have no overhead). Another advantage of EMLIB are the included assertions. These assertions ensure that peripherals are used properly. To enable this, pass `DEBUG_EFM` to your compiler. ### Pin locations The EFM32 platform supports peripherals to be mapped to different pins (predefined locations). The definitions in `periph_conf.h` mostly consist of a location number and the actual pins. The actual pins are required to configure the pins via GPIO driver, while the location is used to map the peripheral to these pins. In other words, these definitions must match. Refer to the data sheet for more information. This MCU has extended pin mapping support. Each pin of a peripheral can be connected separately to one of the predefined pins for that peripheral. ## Flashing the device The board has no integrated programmer/debugger and no bootloader. Hence, an external SWD programmer/debugger such as the [SEGGER JLink][prog-jlink] or the [ST-Link][prog-stlink] is required. Connect at least the SWDIO, SWCLK, and GND to the programmer. If `JLinkExe` is found in `$PATH`, `jlink` is used by default for flashing, otherwise `openocd` is the default. When using OpenOCD, the `stlink` is the default for `OPENOCD_DEBUG_ADAPTER`; provide a different value if you use other hardware. @note When flashing with OpenOCD, leave the NRESET pin unconnected. The configuration does a soft reset only to work around an issue attaching with the hardware reset signal. [prog-jlink]: https://www.segger.com/jlink-software.html [prog-stlink]: https://www.aliexpress.com/wholesale?SearchText=stlink Flashing is supported by RIOT-OS using the command below: ``` make flash ``` To run the GDB debugger, use the command: ``` make debug ``` Or, to connect with your own debugger: ``` make debug-server ``` Some boards have (limited) support for emulation, which can be started with: ``` make emulate ``` ## Supported Toolchains For using the Ebyte E180-ZG120B-TB starter kit we strongly recommend the usage of the [GNU Tools for ARM Embedded Processors](https://developer.arm.com/open-source/gnu-toolchain/gnu-rm) toolchain. ## License information * Ebyte' EMLIB: zlib-style license (permits distribution of source). */