When the NIB is compiled for 6LN mode (but not a 6LBR), the Stateless
Address Autoconfiguration (SLAAC) functionality is disabled, as it is
typically not required; see `sys/include/net/gnrc/ipv6/nib/conf.h`, ll.
46 and 55. However, if a non-6LN interface is also compiled in (still
without making the node a border router) an auto-configured address will
be assigned in accordance with [RFC 6775] to the interface, just
assuming the interface is a 6LN interface. As it then only performs
duplicate address detection RFC-6775-style then, the address then never
becomes valid, as the duplicate address detection according to [RFC
4862] (part of the SLAAC functionality) is never performed.
As auto-configuring an address without SLAAC doesn't make sense, this
fix makes the interface skip it completely, but provides a warning to
the user, so they know what to do.
[RFC 6775]: https://tools.ietf.org/html/rfc6775#section-5.2
[RFC 4862]: https://tools.ietf.org/html/rfc4862#section-5.4
We want to check if the interface is an interface requiring the 6Lo
adaptation layer, not if it is a 6LN according to RFC 6775 [[1]].
[1]: https://tools.ietf.org/html/rfc6775#section-2
When writing to the IPv6 header the implementation currently doesn't
take the packet with the (potentially) duplicated header, but the
packet with the original one, which leads to the packet sent and then
released in `gnrc_netif_ethernet.c` first and then accessed again in
further iterations of the "writing to the IPv6 header" loop, which
causes access to an invalid pointer, causing a crash.
Fixes#11980
While 485dbd1fda (from #12175) was right
in assuming that the for most ICMPv6 error messages the originating
packet's destination address must not be a multicast, this is not the
case for _all_ ICMPv6 error messages (see [RFC 4443], section 2.4(e.3)).
Additionally, 485dbd1fda removed the
check for the source address ([RFC 4443], section 2.4(e.6)), which this
PR re-adds.
[RFC 4443]: https://tools.ietf.org/html/rfc4443#section-2.4
Rather than dispatching the packet automatically once it is complete,
`gnrc_sixlowpan_frag_rb_add()` now only returns success, and leaves it
to the caller to dispatch the packet.
While it is correct to not use an invalid address as a source address,
it is incorrect to assume that addresses not assigned to the interface
(`idx == -1` in the respective piece of code) are invalid: Other than
classic forwarding via a FIB, forwarded packets utilizing a IPv6
routing header will pass this check, like any other packet sent by this
node. The source address for these is not on the given node, so e.g.
source routing is not possible at the moment.
The IPv6 (extension) headers of the first fragment received are re-used
for the reassembled packet, so when receiving a subsequent packet we
need to distinguish, if we just want to release the payload or all of
the packet after the packet data was added to the reassembly buffer.
Due to some changes to the minimal forwarding draft and in preparation
for Selective Fragment Recovery some changes to the VRB API were
needed. Now the index of a VRB entry is only (L2 src, tag) not as
before (L2 src, L2 dst, length, tag).
I know that the current `rbuf_base` causes waste, as all the fields not
used by the new index are effectively not used by the VRB. I'd like to
fix that however in a later change, since that also requires some
modifications of the classic reassembly buffer, and thus would
complicate the review and testing of the change.
Sources for the index change:
- https://tools.ietf.org/html/draft-ietf-6lo-minimal-fragment-04#section-1
- https://mailarchive.ietf.org/arch/browse/6lo/?gbt=1&index=DLCTxC2X4bRNtYPHhtEkavMWlz4
before this commit the src address was checked for multicast, but the dst address should be checked. Therefore udp multicast packets would be flooded back to the src as ICMPv6 error, as not all nodes had a UDP receiver registered.
