This allows to set a timer between the completion of a datagram in the
reassembly buffer and the deletion of the corresponding reassembly
buffer entry. This allows to ignore potentially late incoming link-layer
duplicates of fragments of the datagram that then will have the
reassembly buffer entry be blocked.
This was noted in this [discussion] for classic 6LoWPAN reassembly (and
minimal fragment forwarding) and is recommended in the current
[selective fragment recovery draft][SFR draft].
[discussion]: https://mailarchive.ietf.org/arch/msg/6lo/Ez0tzZDqawVn6AFhYzAFWUOtJns
[SFR draft]: https://tools.ietf.org/html/draft-ietf-6lo-fragment-recovery-07#section-6
The name `fragment_msg` or `frag_msg`/`msg_frag` always to me was a bit
misplaced, as it basically implements an asynchronous fragmentation
buffer and doesn't necessarily have anything to do with messages.
This change
1. changes the name to `fb` (for fragmentation buffer)
2. factors its code out to its own sub-module so it can be re-used by
other 6LoWPAN fragmentation schemes like [Selective Fragment
Recovery]
[Selective Fragment Recovery]: https://tools.ietf.org/html/draft-ietf-6lo-fragment-recovery-05
The interface is already fetched in the beginning of the function and
doesn't change during its run, so getting the interface again at this
point is just redundant.
When decoding IPHC in a fragmented datagram, relying on the size of the
allocated space for the decoded packet is wrong when fragments are
forwarded and decoded on an intermediate node (for which the reassembly
buffer's space is used): Using the full datagram size for allocation in
this case would be wasteful, so the allocated space is only marginally
larger than the fragment's compressed form.
This in turn results in the wrong UDP payload size being chosen and
even worse being forwarded to the subsequent nodes.
This change uses the (virtual) reassembly buffer's `datagram_size`
instead of relying on the allocated space for the encoded
datagram/fragment.
When the NIB is compiled for 6LN mode (but not a 6LBR), the Stateless
Address Autoconfiguration (SLAAC) functionality is disabled, as it is
typically not required; see `sys/include/net/gnrc/ipv6/nib/conf.h`, ll.
46 and 55. However, if a non-6LN interface is also compiled in (still
without making the node a border router) an auto-configured address will
be assigned in accordance with [RFC 6775] to the interface, just
assuming the interface is a 6LN interface. As it then only performs
duplicate address detection RFC-6775-style then, the address then never
becomes valid, as the duplicate address detection according to [RFC
4862] (part of the SLAAC functionality) is never performed.
As auto-configuring an address without SLAAC doesn't make sense, this
fix makes the interface skip it completely, but provides a warning to
the user, so they know what to do.
[RFC 6775]: https://tools.ietf.org/html/rfc6775#section-5.2
[RFC 4862]: https://tools.ietf.org/html/rfc4862#section-5.4
We want to check if the interface is an interface requiring the 6Lo
adaptation layer, not if it is a 6LN according to RFC 6775 [[1]].
[1]: https://tools.ietf.org/html/rfc6775#section-2
When writing to the IPv6 header the implementation currently doesn't
take the packet with the (potentially) duplicated header, but the
packet with the original one, which leads to the packet sent and then
released in `gnrc_netif_ethernet.c` first and then accessed again in
further iterations of the "writing to the IPv6 header" loop, which
causes access to an invalid pointer, causing a crash.
Fixes#11980
While 485dbd1fda (from #12175) was right
in assuming that the for most ICMPv6 error messages the originating
packet's destination address must not be a multicast, this is not the
case for _all_ ICMPv6 error messages (see [RFC 4443], section 2.4(e.3)).
Additionally, 485dbd1fda removed the
check for the source address ([RFC 4443], section 2.4(e.6)), which this
PR re-adds.
[RFC 4443]: https://tools.ietf.org/html/rfc4443#section-2.4
Rather than dispatching the packet automatically once it is complete,
`gnrc_sixlowpan_frag_rb_add()` now only returns success, and leaves it
to the caller to dispatch the packet.
While it is correct to not use an invalid address as a source address,
it is incorrect to assume that addresses not assigned to the interface
(`idx == -1` in the respective piece of code) are invalid: Other than
classic forwarding via a FIB, forwarded packets utilizing a IPv6
routing header will pass this check, like any other packet sent by this
node. The source address for these is not on the given node, so e.g.
source routing is not possible at the moment.
The IPv6 (extension) headers of the first fragment received are re-used
for the reassembled packet, so when receiving a subsequent packet we
need to distinguish, if we just want to release the payload or all of
the packet after the packet data was added to the reassembly buffer.
Due to some changes to the minimal forwarding draft and in preparation
for Selective Fragment Recovery some changes to the VRB API were
needed. Now the index of a VRB entry is only (L2 src, tag) not as
before (L2 src, L2 dst, length, tag).
I know that the current `rbuf_base` causes waste, as all the fields not
used by the new index are effectively not used by the VRB. I'd like to
fix that however in a later change, since that also requires some
modifications of the classic reassembly buffer, and thus would
complicate the review and testing of the change.
Sources for the index change:
- https://tools.ietf.org/html/draft-ietf-6lo-minimal-fragment-04#section-1
- https://mailarchive.ietf.org/arch/browse/6lo/?gbt=1&index=DLCTxC2X4bRNtYPHhtEkavMWlz4
