During production it is often desirable for devices to perform
some kind of basic self-test to isolate defects.
For this it is necessary for the initialization not to hang if a
component is faulty / not connected.
This moves an already exising self-test that was previously enabled
as a debug option to an independent compile-time configurable.
It is necessary to call this in _init() before mrf24j40_hardware_reset()
as the reset function uses xtimer_usleep() which will cause another
thread to get scheduled.
If this thread (e.g. rpl or ipv6) then tries to access the netdev, RIOT
will crash.
Change documentation on return codes in periph/timer API to
return 0 on success and (-1) on error by default.
For timer_init this was already the case, but for timer_set,
timer_set_absolute, and timer_clear this is now changed
from 1 to 0 for success, while error remains (-1).
This (re-)introduces the `CC110X_DEFAULT_CHANNEL` preprocessor macro to set the
default channel of the `cc110x` at compile time. The same macro has been used
in the previous version of the driver, so some users might still expect it to
work.
The Atlas Scientific pH OEM sensor is a small circuit to be embedded in
end products to measure the pH value with any commercially available pH
electrode
Rename TMP006 to TMP00x
Add TMP007 sensor support to TMP00X
Change uint8_t reg to uint16_t
Add to doxygen documentation group
Expose compile time configurations
Move defines from .c to .h
Change double to float, because double is not needed
Add TMP007 register information
i2c_release() should not have a return value, as:
- There is no reasonable error handling possible by the caller, so there is no
value in indicating success/failure via the return value to the caller
- There is no legitimate reason to fail *unless* an invalid I2C bus was released
or an I2C bus that was not previously acquired was released
--> This would indicate a bug in the code and should be tackled by an
assert()
The cc110x driver has been re-written from scratch to overcome the limitations
of the old driver. The main motivation of the rewrite was to achieve better
maintainability by a detailed documentation, reduce the complexity and the
overhead of the SPI communication with the device, and to allow to
simultaneously use transceivers with different configuration regarding the used
base band, the channel bandwidth, the modulation rate, and the channel map.
Features of this driver include:
- Support for the CC1100, CC1101, and the CC1100e sub-gigahertz transceivers.
- Detailed documentation of every aspect of this driver.
- An easy to use configuration API that allows setting the transceiver
configuration (modulation rate, channel bandwidth, base frequency) and the
channel map.
- Fast channel hopping by pre-calibration of the channels during device
configuration (so that no calibration is needed during hopping).
- Simplified SPI communication: Only during start-up the MCU has to wait
for the transceiver to be ready (for the power regulators and the crystal
to stabilize). The old driver did this for every SPI transfer, which
resulted in complex communication code. This driver will wait on start up
for the transceiver to power up and then use RIOT's SPI API like every other
driver. (Not only the data sheet states that this is fine, it also proved to
be reliable in practise.)
- Greatly reduced latency: The RTT on the old driver (@150 kbps data rate) was
about 16ms, the new driver (@250 kbps data rate) has as RTT of ~3ms
(depending on SPI clock and on CPU performance) (measured with ping6).
- Increased reliability: The preamble size and the sync word size have been
doubled compared to the old driver (preamble: 8 bytes instead of 4,
sync word: 4 byte instead of 2). The new values are the once recommended by
the data sheet for reliable communication.
- Basic diagnostic during driver initialization to detect common issues as
SPI communication issues and GDO pin configuration/wiring issues.
- TX power configuration with netdev_driver_t::set() API-integration
- Calls to netdev_driver_t::send() block until the transmission has completed
to ease the use of the API (implemented without busy waiting, so that the
MCU can enter lower power states or other threads can be executed).
- Removed cc110x driver
- Updated all makefiles
- Kept both board specific configurations and support for it in RIOT's
upper layers, so re-implementations don't need to start from zero
