Rename TMP006 to TMP00x
Add TMP007 sensor support to TMP00X
Change uint8_t reg to uint16_t
Add to doxygen documentation group
Expose compile time configurations
Move defines from .c to .h
Change double to float, because double is not needed
Add TMP007 register information
The value must be saved from the original value to allow restoring it.
This has currently no impact on 'info-boards-supported' as it is
currently ignored.
By default if a test is available and not blacklisted it will be run by
murdock.
This will move from a whitelisting everything that works, to
blacklisting what fails. This way, failing tests will be easier to
track instead of being silently just not run.
It could even allow introducing failing tests before a fix is available.
Only set `TEST_ON_CI_ENABLED` if the application has tests.
Currently `TEST_ON_CI_WHITELIST` was only set if there were tests.
This is a pre-step to have `TEST_ON_CI_WHITELIST` being `all` by
default.
The cc110x driver has been re-written from scratch to overcome the limitations
of the old driver. The main motivation of the rewrite was to achieve better
maintainability by a detailed documentation, reduce the complexity and the
overhead of the SPI communication with the device, and to allow to
simultaneously use transceivers with different configuration regarding the used
base band, the channel bandwidth, the modulation rate, and the channel map.
Features of this driver include:
- Support for the CC1100, CC1101, and the CC1100e sub-gigahertz transceivers.
- Detailed documentation of every aspect of this driver.
- An easy to use configuration API that allows setting the transceiver
configuration (modulation rate, channel bandwidth, base frequency) and the
channel map.
- Fast channel hopping by pre-calibration of the channels during device
configuration (so that no calibration is needed during hopping).
- Simplified SPI communication: Only during start-up the MCU has to wait
for the transceiver to be ready (for the power regulators and the crystal
to stabilize). The old driver did this for every SPI transfer, which
resulted in complex communication code. This driver will wait on start up
for the transceiver to power up and then use RIOT's SPI API like every other
driver. (Not only the data sheet states that this is fine, it also proved to
be reliable in practise.)
- Greatly reduced latency: The RTT on the old driver (@150 kbps data rate) was
about 16ms, the new driver (@250 kbps data rate) has as RTT of ~3ms
(depending on SPI clock and on CPU performance) (measured with ping6).
- Increased reliability: The preamble size and the sync word size have been
doubled compared to the old driver (preamble: 8 bytes instead of 4,
sync word: 4 byte instead of 2). The new values are the once recommended by
the data sheet for reliable communication.
- Basic diagnostic during driver initialization to detect common issues as
SPI communication issues and GDO pin configuration/wiring issues.
- TX power configuration with netdev_driver_t::set() API-integration
- Calls to netdev_driver_t::send() block until the transmission has completed
to ease the use of the API (implemented without busy waiting, so that the
MCU can enter lower power states or other threads can be executed).
This allows passing other arguments as environment variables in
DOCKER_ENVIRONMENT_CMDLINE and as command line override in
DOCKER_OVERRIDE_CMDLINE without using the automatic detection.
This will allow passing USEMODULE to docker as its value is usually set
in an application Makefile so has its origin changed.
This allows setting other variables that should be exported to the
docker build.
As for other variables, they must still be unmodified before parsing
`docker.inc.mk` to be exported.
The value must be saved from the original value to allow restoring it.
This has currently no impact as 'makefiles/defaultmodules.inc.mk'
and 'DISABLE_MODULE' are ignored in this parsing.
This remove executing buildtest `for` loop in docker.
When building completely in docker, 'buildtest' would hide issues when
the host toolchain would be used when doing `make all` directly.
It has the consequence that it now starts a container for each
compilation which is slower.
The previous behavior can be reproduced by using
BUILD_IN_DOCKER=1 make buildtest-indocker
A side effect is also that now `BUILDTEST_MAKE_REDIRECT` would work when
doing `buildtest` with docker.
Add a 'buildtest-indocker' that forces executing 'buildtest' for loop
completely inside the container.
It prevents starting one container per compilation wich is slower but
it could hide errors where the host toolchain would be used
It is currently equivalent to `buildtest` but will change when the
`buidtest` handling will be move outside of `BUILD_IN_DOCKER`.
Display an error when executed without BUILD_IN_DOCKER=1.
Move git version evaluation to a separate file.
The definition has been updated it to a deferred only definition.
This way git is not called when GIT_VERSION is not used.
Document `BINFILE` in the same ways as `HEXFILE`.
The file does not need to be exported so no reason to do it though.
It also adds it in the `info-build` output in the same way as `HEXFILE`.
Previously, this was hard-coded to allow one file, hard-coded to be
called "flash file".
This commit allows multiple files to be specified via adding them to the
TEST_EXTRA_FILES variable. All files will be stored in the worker's
application bin directory.
Also, the existence check has been removed, as dwqc bails out on missing
file anyways.
... if the riotboot feature is used.
Previously, even an application that had "FEATURES_REQUIRED += riotboot"
set would still flash the non-riotboot binary on "make flash".
This is usualy not what the user wants.
This commit set's the FLASHFILE variable to the combined "riotboot
bootloader + slot0 + empty slot1" binary. This has the effect that make
all, flash and flash-only will compile and/or flash a working riotboot
setup.
tests/riotboot and tests/riotboot_flashwrite now default to flashing the
riotboot-extended binary. tests/riotboot was previously configured to
use the riotboot-combined binary. This has been changed in order to not
behave differently than how usual riotboot applications do.
Introduce a variable to set that a test is blacklisted.
This is a move toward enabling tests by default and adding a blacklisting
reason instead for a board instead of not whitelisting them which hides
the problem.
Currently, a test should be both whitelisted and blacklisted at the same
time to have a meaning. It is planned to whitelist all by default in
an upcoming pull request.
Refactor the handling to use a variable to store if a test is enabled.
Add a 'test-on-ci-enabled' target that test if the test on ci is enabled.
This is a first commit before changing the behavior.
