MrKevinWeiss
e0fdc3c16c
*Kconfig*: Modify Kconfig to remove dep model
2024-03-27 10:28:12 +01:00
Benjamin Valentin
5d111e71aa
boards: drop board_init() from board.h
2022-02-25 15:08:58 +01:00
Leandro Lanzieri
f684ecfd5c
boards: model avr-based boards Kconfig
...
Modelled boards:
arduino-duemilanove
arduino-leonardo
arduino-mega2560
arduino-nano
arduino-uno
atmega1284p
atmega256rfr2-xpro
atmega328p-xplained-mini
atmega328p
atxmega-a1-xplained
atxmega-a1u-xpro
atxmega-a3bu-xplained
avr-rss2
derfmega128
derfmega256
mega-xplained
microduino-corerf
zigduino
2021-11-22 12:25:30 +01:00
c6ad85a7b0
boards: don't include programmer logic at board level
2020-11-25 22:31:13 +01:00
Benjamin Valentin
c29825a173
boards/microduino-corerf: don't set bootloader size
...
This already gets set by `common/atmega/Makefile.include`.
Setting it in the board prevents auto-selection if a bootloader
is used.
2020-10-14 23:37:42 +02:00
Leandro Lanzieri
15cef2bc74
boards/microduino-corerf: Add Kconfig symbols
2020-06-22 16:10:41 +02:00
Marian Buschsieweke
966b0e22e5
boards/microduino-corerf: Fix duplicated includes
...
avrdude.mk and serial.mk was included twice. As a result of the former, avrdude
wasted one flash cycle and some time by writing the same firmware twice.
2020-05-12 15:00:14 +02:00
Marian Buschsieweke
72e497c0c3
boards/microduino-corerf: Added OCD doc
2020-03-10 20:13:18 +01:00
Benjamin Valentin
1dd260b446
boards: enable RTC for every ATmega board that supports RTT
...
Every ATmega board that can run an Real Time Timer can also run
an emulated Real Time Clock.
Got all supported boards by adding `FEATURES_REQUIRED += arch_8bit`
to `tests/periph_rtt` and running
sed -i 's/FEATURES_PROVIDED += periph_rtt/
FEATURES_PROVIDED += periph_rtc\n
FEATURES_PROVIDED += periph_rtt/g'
on them.
2020-03-03 16:27:44 +01:00
benpicco
03b95ef833
Merge pull request #12883 from fabian18/microduino-corerf-doc-pin-mapping
...
boards/microduino-corerf: doc SPI and I2C pin mapping
2019-12-05 21:14:05 +01:00
fabian18
f3f4c3b4b8
boards/microduino-corerf: doc SPI and I2C pin mapping
2019-12-05 19:43:35 +01:00
Benjamin Valentin
472373637c
boards/microduino-corerf: enable RTT
...
The board *does* have a crystal oscillator connected, so we can
enable RTT.
2019-12-04 22:45:18 +01:00
Benjamin Valentin
e958798225
boards/microduino-corerf: use 115200 baud for stdio
...
The MCU can handle that baud rate just fine.
A standard baud rate is much easier to use than those awkward 57600 baud.
2019-12-04 22:43:41 +01:00
Marian Buschsieweke
fa3651f275
boards/microduino-corerf: Minor doc tweaks
...
- Using @warning Doxygen command to make warning more visible
- Used IEC units for size specifications
- Aligned markdown source of the table
- Added note that the 5V pin is not connected to the board and cannot be used
to power the board
2019-10-30 08:51:34 +01:00
27f2a19f72
boards/atmega: remove useless provided gpio features
...
These features are provided at CPU level
2019-10-17 21:42:49 +02:00
Benjamin Valentin
20906328b4
boards/microduino-corerf: Initial board support
2019-10-17 19:20:31 +02:00
