RIOT supports two distinct families of the MSP430: The [MSP430 x1xx]
MCU family and the [MSP430 F2xx/G2xx] MCU family. For both incompatible
MCU families the code was located in the msp430fxyz folder, resulting
in case of the UART driver in particularly bizarre code looking roughly
like this:
#ifndef UART_USE_USCI
/* implementation of x1xx peripheral ... */
#else
/* implementation of F2xx/G2xx peripheral ... */
#endif
/* zero shared code between both variants */
This splits the peripheral drivers for USCI and USART serial IP blocks
into separate files and relocates everything in cpu/msp430, similar to
how cpu/stm32 is organized.
[MSP430 x1xx]: https://www.ti.com/lit/ug/slau049f/slau049f.pdf
[MSP430 F2xx/G2xx]: https://www.ti.com/lit/ug/slau144k/slau144k.pdf
Provide a common clock initialization driver rather than leaving
clock initialization to the boards code. A declarative description of
the board's clock configuration using a struct does still allow to
fine-tune settings. In addition, a board is still allowed to just
provide a custom `void clock_init(void)` if there really is the need
to do crazy things.
cpu/$(CPU)/Makefile.features and cpu/$(CPU)/Makefile.dep are
automatically included
Part of moving CPU/CPU_MODEL definition to Makefile.features to have it
available before Makefile.include.
MSPDEBUGFLAGS is evaluated only in the same file.
Its value does not need to be exported.
This will also prevent evaluating 'PORT' for MSPDEBUGFLAGS when not needed.
DEBUGGER/DEBUGGER_FLAGS/DEBUGSERVER/DEBUGSERVER_FLAGS are evaluated by the
main Makefile.include or by file included by it.
Their value does not need to be exported.
Testing
-------
`git diff --word-diff` only reports `export` being removed.
`git show --stat` reports `55 insertions(+), 55 deletions(-)`
Which is the same amount as lines that where matching
`export[[:blank::]]\+VARIABLE`.
FLASHER and FFLAGS are evaluated by the main Makefile.include or by file
included by it. Their value does not need to be exported.
This will also prevent evaluating 'PORT' for FFLAGS when not needed.
Testing
-------
`git diff --word-diff` only reports `export` being removed.
`git show --stat` reports `84 insertions(+), 84 deletions(-)`
Which is the same amount as lines that where matching
`export[[:blank::]]\+VARIABLE`.
The file always exist so no need to do '-include'.
Replaced using:
sed -i 's|-\(include $(RIOTCPU)/.*/Makefile.features\)|\1|' \
$(git grep -l '$(RIOTCPU)/.*/Makefile.features' boards)
- Use RIOT's GPIO interface to access the sensor to increase portability
- Changed API to allow more than one sensor per board
- Added `sht1x_params.h` that specifies how the sensors is connected - each
board can overwrite default settings by #defining SHT1X_PARAM_CLK and
SHT1X_PARAM_DATA
- Changed arithmetic to use integer calculations only instead of floating point
arithmetic
- Added support for checking the CRC sum
- Allow optional skipping of the CRC check to speed up measuring
- Added support for advanced features like reducing the resolution and skipping
calibration to speed up measuring
- Allow specifying the supply voltage of sensor which heavily influences the
temperature result (and use that information to calculate the correct
temperature)
- Reset sensor on initialization to bring it in a well known state
- Support for the obscure heater feature. (Can be useful to check the
temperature sensor?)
- Updated old SHT11 shell commands to the new driver interface, thus allowing
more than one SHT10/11/15 sensor to be used
- Added new shell command to allow full configuration of all attached SHT1x
sensors
- Removed old command for setting the SHT11 temperature offset, as this feature
is implemented in the new configuration command
The sensor family SHT10, SHT11 and SHT15 only differ in their accuracy (as in
calibration, not as in resolution). Thus, the same driver can be used for all.
The new driver name better reflects this fact.
