This adds a driver for the ST M95xxx series SPI EEPROMs.
The driver has been tested with the M95M01 EEPROM, but should
work with other chips from that family.
SPI-EEPROMs from other vendors from the families AT25xxx, 25AAxxx,
25LCxxx, CAT25xxx & BR25Sxxx should also in the same way.
Previously the function attempted to block here and manually service
the ISR.
This lead to unexpected results, in particular messages queuing up in
the threads message queue.
The result was that the radio would not end up in the correct state.
E.g. sending SLEEP to both interfaces while a transmission was ongoing
would lead to the interfaces waking up again.
With this patch the operation will just return -ERRNO so the caller can
try again.
To reproduce, try the attached patch for the `gnrc_networking` example:
On master you will find that the radio still consumes ~2.4mA after 'shutdown'.
(It is in fact in the state TRXOFF as it woke up again)
With this change the radio should consume less than 1µA (DEEP SLEEP).
diff --git a/examples/gnrc_networking/main.c b/examples/gnrc_networking/main.c
index 6301f4291d..93b96eb939 100644
--- a/examples/gnrc_networking/main.c
+++ b/examples/gnrc_networking/main.c
@@ -23,12 +23,47 @@
#include "shell.h"
#include "msg.h"
+#include "periph/pm.h"
+
+#include "net/netopt.h"
+#include "net/gnrc/netif.h"
+
#define MAIN_QUEUE_SIZE (8)
static msg_t _main_msg_queue[MAIN_QUEUE_SIZE];
extern int udp_cmd(int argc, char **argv);
+extern void send(char *addr_str, char *port_str, char *data, unsigned int num,
+ unsigned int delay);
+
+static int send_and_shutdown(int argc, char **argv)
+{
+ (void) argc;
+ (void) argv;
+
+ /* the address must not exist */
+ char addr[] = "fe80::2068:3123:59f5:d238%7";
+ char port[] = "1234";
+ char data[] = "Hello World!";
+
+ send(addr, port, data, 1, 0);
+
+ /* disable radio */
+ gnrc_netif_t* netif = NULL;
+ netopt_state_t state = NETOPT_STATE_SLEEP;
+ while ((netif = gnrc_netif_iter(netif))) {
+ /* retry while busy */
+ while (gnrc_netapi_set(netif->pid, NETOPT_STATE, 0, &state,
+ sizeof(netopt_state_t)) == -EBUSY);
+ }
+
+ pm_set(0);
+
+ return 0;
+}
+
static const shell_command_t shell_commands[] = {
+ { "shutdown", "turn off the radio & shut down", send_and_shutdown },
{ "udp", "send data over UDP and listen on UDP ports", udp_cmd },
{ NULL, NULL, NULL }
};
diff --git a/examples/gnrc_networking/udp.c b/examples/gnrc_networking/udp.c
index e8a559846e..cb80855b76 100644
--- a/examples/gnrc_networking/udp.c
+++ b/examples/gnrc_networking/udp.c
@@ -36,7 +36,7 @@ static gnrc_netreg_entry_t server = GNRC_NETREG_ENTRY_INIT_PID(GNRC_NETREG_DEMUX
KERNEL_PID_UNDEF);
-static void send(char *addr_str, char *port_str, char *data, unsigned int num,
+void send(char *addr_str, char *port_str, char *data, unsigned int num,
unsigned int delay)
{
gnrc_netif_t *netif = NULL;
When the radio is in DEEP SLEEP, reading the state register will return 0.
This makes the reset routine abort early even though the device is connected
and still waking up.
Instead, just add a timeout to the polling of the WAKEUP IRQ bit.
In practise it has shown that the loop will be taken two times on 'normal'
reset and four times when the radio was in DEEP SLEEP.
Polling 255 times sure does not hurt.
To reproduce the issue, put both interfaces into SLEEP mode,
then reboot the module:
ifconfig 7 set state sleep
ifconfig 8 set state sleep
reboot
- Since flash access is shared with CPU2 we resize ROM_LEN
according to CPU2 secure flash memmory area.
- Add assert to prevent unauthorized reads from CPU2 secure
flash area
Previously the default config was for connecting the REB215-XPRO
module to EXT3 on same54-xpro.
Since now more SPI buses are configured on same54-xpro and the default
config also serves as a compile test for boards with only one SPI bus,
connect the module to the (new) first SPI bus by default.
This is the radio found in NXP Kinetis KW41Z, KW21Z. Only 802.15.4 mode
is implemented (KW41Z also supports BLE on the same transceiver).
The driver uses vendor supplied initialization code for the low level
XCVR hardware, these files were imported from KSDK 2.2.0 (framework_5.3.5)
