20003: coap: create typedef for CoAP methods r=benpicco a=benpicco
20028: nanocoap: fix incorrect uses of coap_get_code() r=benpicco a=benpicco
20036: boards/nucleo-l4r5zi : add PWM configuration r=benpicco a=krzysztof-cabaj
### Contribution description
This PR adds to the Nucleo-l4r5zi PWM configuration
### Testing procedure
Flash the board using `tests/periph/pwm` program. Check if you could, for example, change LED
intensity using PWM.
### Issues/PRs references
None.
20041: pkg/littlefs2: bump to v2.8.1 r=benpicco a=bergzand
### Contribution description
Minor version number bump.
### Testing procedure
- Check if I copied the correct commit hash.
- Run the tests.
### Issues/PRs references
None
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Co-authored-by: krzysztof-cabaj <kcabaj@gmail.com>
Co-authored-by: Koen Zandberg <koen@bergzand.net>
Router Advertisements are enabled automatically for routing nodes
as soon as they obtain a prefix (e.g. via DHCPv6, UHCP, …).
Enabling router advertisements without a prefix to advertise is
wrong and causes no router solicitations to be send on an upstream
interface.
Also from https://www.rfc-editor.org/rfc/rfc4861#section-6.2.1
Note that AdvSendAdvertisements MUST be FALSE by
default so that a node will not accidentally start
acting as a router unless it is explicitly
configured by system management to send Router
Advertisements.
19876: sys/net/ipv4/addr: fix typos r=benpicco a=Enoch247
### Contribution description
This patch fixes some typos in the doxygen doc.
### Testing procedure
Nothing to test. No change to code.
### Issues/PRs references
- None known
19878: makefiles/usb_board_reset.mk: declare term-delay target with test target r=benpicco a=aabadie
19888: boards/sltb009a: complete and fix documentation r=benpicco a=gschorcht
### Contribution description
This PR completes and fixes the documentation which was still in the state as generated automatically by `efm2riot`.
The PR also includes a fix of the configuration of the second UART device that was find out while completing the documentation.
### Testing procedure
Green CI
### Issues/PRs references
Co-authored-by: Joshua DeWeese <jdeweese@primecontrols.com>
Co-authored-by: Alexandre Abadie <alexandre.abadie@inria.fr>
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
19487: nanocoap: implement extended tokens (RFC 8974) r=benpicco a=benpicco
19808: boards: add ESP32-S3-USB-OTG support r=benpicco a=gschorcht
### Contribution description
This PR provides the support for the [ESP32-S3-USB-OTG](https://docs.espressif.com/projects/espressif-esp-dev-kits/en/latest/esp32s3/esp32-s3-usb-otg/user_guide.html) board.
The SD card can only be used in SPI mode at the moment. As soon as PR #19786 is merged, the SD/MMC support can be enabled and the SD card can then be used in SD mode with 4-bit data bus width.
The display uses uses the ST7789 driver IC that is compatible with the ST7735. For that purpose the ST7735 driver is extended by a pseudomodule definition `st7789` for the ST7789 which is enabled by the board and enables automatically the `st7789` (e57c48a33ee2a869c15603788e5306ba066f91cf). Vise versa, board's `Makefile.dep` enables automatically the `st7789` pseudomodule if the `st7735` is used. The pseudomodule `st7789` is just used to increase the upper limit for supported lines. This change is also part of PR #19807.
~The PR includes a very small documentation fix for ESP32-S3-DevKit board that was noticed during the development of this board definition (1155b6ac1b8efa39d8a0bd7150e602095159fdc1).~
### Testing procedure
The board has been tested with all basic tests for supported hardware including `tests/driver/st3375`:
- [x] tests/drivers/st3375
- [x] tests/periph/gpio
- [x] tests/periph/pwm
- [x] tests/periph/spi
- [x] tests/periph/uart
- [x] tests/sys/usbus_cdc_ecm
### Issues/PRs references
Co-authored-by: Benjamin Valentin <benpicco@beuth-hochschule.de>
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
