The esp8266 CPU has actually two hardware UART peripherals. UART0 is
used by the boot ROM for flashing and serial output during boot,
typically at a baudrate of 74880 bps until the bootloader or application
sets the more standard 115200 baudrate. This UART0 device has two
possible pins for TXD, GPIO1 and GPIO2, which are both set to TXD by the
boot ROM. esp8266 modules will typically have GPIO1 labeled as the TX
pin, but it is possible to use GPIO2 for that purpose even while
flashing the device with esptool.py.
The second device, UART1, also has two options for TXD, GPIO2 and GPIO7,
and only one option for RXD, GPIO8. However, GPIO7 and GPIO8 are used
by the flash internally so those options are not very useful unless
maybe while running from IRAM with the flash disabled, for example for
a debugger over UART1.
This patch allows boards to override UART{0,1}_{R,T}XD in their
periph_conf.h to configure the uart selection. Defining UART1_TX will
make the UART_DEV(1) device available.
Tested with:
```CFLAGS='-DUART1_TXD=GPIO2' make -C tests/periph_uart BOARD=esp8266-esp-12x flash term```
* Connected one USB-UART to the standard GPIO1 and GPIO3 for flashing
and console. After flashing we see the manual test output at 115200
bps
* Connected a second USB-UART with RX to GPIO2 running at 74880.
Then run on the first console:
```
> init 1 74880
> send 1 hello
```
The word "hello" appears on the second UART connection.
Note that GPIO2 is used during boot for UART0's TX until the application
or bootloader set it to a regular GPIO, so some boot ROM messages at
74880 bps are visible. After running `init 1 74880` it is set to UART1's
TX.
The RTT overflow callback is not available on all RTT implementations.
This means it is either a no-op or `rtt_set_overflow_cb()` is a no-op
or it will overwrite the alarm set with `rtt_set_alarm()`.
This adds a feature to indicate that proper overflow reporting is available.
The extra `)` was a typo from the commit that changes the makefile
inline "if" to a multi-line "if" block.
Tested with `USEMODULE="esp_gdbstub" make BOARD=esp8266-esp-12x -C tests/lwip`
Some periph_rtt implementations do not provide `rtt_set_counter()`. This
adds `periph_rtt_set_counter` as feature to allow testing for its
availability. The feature is provided at CPU level if periph_rtt is
provided by the board for all CPUs implementing `rtt_set_counter()`.
Some periph_rtt implementations do not provide `rtt_set_counter()`. This
adds `periph_rtt_set_counter` as feature to allow testing for its
availability. The feature is provided at CPU level if periph_rtt is
provided by the board for all CPUs implementing `rtt_set_counter()`.
- Add `WORD_ALIGNED` attribute to potentially unaligned allocations
- Use intermediate cast to `uintptr_t` to silence false positives of
`-Wcast-align`
This is an implementation of the ESP32 SoftAP mode using the
`esp_wifi_ap` pseudomodule.
Signed-off-by: Jean Pierre Dudey <jeandudey@hotmail.com>
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
Add `TARGET_ARCH_<ARCH>` for each architecture (e.g. `TARGET_ARCH_CORTEX` for
Cortex M) to allow users to overwrite the target triple for a specific arch
from ~/.profile or ~/.bashrc (or the like) without overwriting it for all others
as well.
To be able to define common configurations for all ESP CPUs, the CPU specific configuration cpu_conf.h has to include a common configuration. For that purpose cpu_conf.h in cpu/esp_common is renamed to cpu_conf_common.h and included in CPU specific configurations.
