Otherwise the function will only displays the first 256 ASCII representation of the bytes in a loop
Signed-off-by: Dylan Laduranty <dylan.laduranty@mesotic.com>
19733: cpu/msp430: reorganize code r=maribu a=maribu
### Contribution description
RIOT supports two distinct families of the MSP430: The [MSP430 x1xx] MCU family and the [MSP430 F2xx/G2xx] MCU family. For both incompatible MCU families the code was located in the msp430fxyz folder, resulting in case of the UART driver in particularly bizarre code looking roughly like this:
```C
#ifndef UART_USE_USCI
/* implementation of x1xx peripheral ... */
#else
/* implementation of F2xx/G2xx peripheral ... */
#endif
/* zero shared code between both variants */
```
This moves peripheral drivers shared between the two families to msp430_common and splits the SPI and UART driver into two MCU families.
In addition, it cleans up the `msp430_regs.h` by dropping most of it and using the macros and symbols provided by the vendor header files. There is little reason for us to maintain constants when TI is already doing that.
[MSP430 x1xx]: https://www.ti.com/lit/ug/slau049f/slau049f.pdf
[MSP430 F2xx/G2xx]: https://www.ti.com/lit/ug/slau144k/slau144k.pdf
19747: gnrc/ipv6/nib: reset rs_sent counter also for not-6LN interfaces r=maribu a=fabian18
19769: cpu/nrf53: add initial support with nRF5340DK-APP board r=maribu a=dylad
### Contribution description
This PR adds support for nRF5340 MCU and its associated Nordic development board, nRF5340DK.
This MCU provides a dual Cortex-M33, one application core running at up to 128MHz, and one network core running at up to 64MHz.
Peripherals are inherited from others Nordic MCUs families so it shouldn't be hard to add more of them in followup PRs.
For now, only the minimal set of peripherals is supported:
- GPIO / GPIO_IRQ
- UART
- TIMER
### Testing procedure
Build the usual test application for the supported peripherals and flash the board.
nRF5340DK provides two serial ports on its embedded debugger. RIOT's shell should be available on the first one (/dev/ttyACM0)
### Issues/PRs references
#18576#19267
19782: cpu/msp430: fix for ti's msp430-gcc-opensource package ld version r=maribu a=hugueslarrive
### Contribution description
My msp430 toolchain (https://www.ti.com/tool/MSP430-GCC-OPENSOURCE) was broken by #19484:
```
hugues@p700:~/github/cpu_msp430_common/RIOT$ BOARD=msb-430 make -j64 -C examples/hello-world
make : on entre dans le répertoire « /home/hugues/github/cpu_msp430_common/RIOT/examples/hello-world »
Building application "hello-world" for "msb-430" with MCU "msp430fxyz".
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/boards/common/init
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/boards/msb-430
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/core
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/core/lib
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/cpu/msp430fxyz
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/drivers
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/boards/common/msb-430
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/drivers/periph_common
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/auto_init
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/div
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/libc
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/malloc_thread_safe
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/cpu/msp430_common
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/newlib_syscalls_default
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/cpu/msp430fxyz/periph
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/preprocessor
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/stdio_uart
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/cpu/msp430_common/periph
/opt/ti/msp430-gcc/bin/../lib/gcc/msp430-elf/9.3.1/../../../../msp430-elf/bin/ld: .rodata not found for insert
collect2: error: ld returned 1 exit status
make: *** [/home/hugues/github/cpu_msp430_common/RIOT/examples/hello-world/../../Makefile.include:761 : /home/hugues/github/cpu_msp430_common/RIOT/examples/hello-world/bin/msb-430/hello-world.elf] Erreur 1
make : on quitte le répertoire « /home/hugues/github/cpu_msp430_common/RIOT/examples/hello-world »
hugues@p700:~/github/cpu_msp430_common/RIOT$ /opt/ti/msp430-gcc/msp430-elf/bin/ld --version
GNU ld (Mitto Systems Limited - msp430-gcc 9.3.1.11) 2.34
Copyright (C) 2020 Free Software Foundation, Inc.
This program is free software; you may redistribute it under the terms of
the GNU General Public License version 3 or (at your option) a later version.
This program has absolutely no warranty.
hugues@p700:~/github/cpu_msp430_common/RIOT$ /opt/ti/msp430-gcc/msp430-elf/bin/ld --version | grep -Eo '[0-9]\.[0-9]+'
9.3
1.11
2.34
hugues@p700:~/github/cpu_msp430_common/RIOT$ /opt/ti/msp430-gcc/msp430-elf/bin/ld --version | grep -Eo '[0-9]\.[0-9]+$'
2.34
```
### Testing procedure
```
hugues@p700:~/github/cpu_msp430_common/RIOT$ BOARD=msb-430 make -j64 -C examples/hello-world
make : on entre dans le répertoire « /home/hugues/github/cpu_msp430_common/RIOT/examples/hello-world »
Building application "hello-world" for "msb-430" with MCU "msp430fxyz".
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/boards/common/init
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/boards/msb-430
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/core
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/core/lib
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/cpu/msp430fxyz
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/drivers
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/boards/common/msb-430
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/drivers/periph_common
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/auto_init
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/div
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/libc
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/malloc_thread_safe
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/newlib_syscalls_default
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/preprocessor
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/cpu/msp430_common
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/sys/stdio_uart
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/cpu/msp430fxyz/periph
"make" -C /home/hugues/github/cpu_msp430_common/RIOT/cpu/msp430_common/periph
text data bss dec hex filename
8612 722 866 10200 27d8 /home/hugues/github/cpu_msp430_common/RIOT/examples/hello-world/bin/msb-430/hello-world.elf
make : on quitte le répertoire « /home/hugues/github/cpu_msp430_common/RIOT/examples/hello-world »
```
### Issues/PRs references
Introduced by #19484, highlighted in #16727.
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@posteo.net>
Co-authored-by: Fabian Hüßler <fabian.huessler@ml-pa.com>
Co-authored-by: Dylan Laduranty <dylan.laduranty@mesotic.com>
Co-authored-by: Hugues Larrive <hlarrive@pm.me>
This allows using the arduino_pwm feature (which is translated into a
module) without the arduino module; e.g. for only using the Arduino
I/O mapping but not the Arduino API.
- Rename all `arduino_pinmap.h` to `arduino_iomap.h`
- An empty `arduino_pinmap.h` that just includes `arduino_iomap.h`
is provided for backward compatibility
- Move all info from `arduino_board.h` into the new file as trivial
macros, so that they can also be used outside of sketches
- The new name reflects the fact not just pin mappings, but also
other I/O features such as PWMs are mapped
- Drop all `arduino_board.h`
- `arduino_board.h` and `arduino_iomap.h` now provide the exact
same information, just in a different format
- a generic `arduino_board.h` is provided instead that just
uses the info in `arduinio_iomap.h` and provides them in the
format the code in `sys/arduino` expects it
- Add fine grained features to indicate for mappings
- availability of mappings for analog pins, DAC pins, PWM pins,
UART devices, SPI/I2C buses to the corresponding RIOT
identification can now be expressed:
- `arduino_pins`: `ARDUINO_PIN_0` etc. are available
- `arduino_analog`: `ARDUINO_A0` etc. are available
- `arduino_pwm`: `ARDUINO_PIN_13_PWM_DEV` etc. are available
- `arduino_dac`: `ARDUINO_DAC0` etc. are available
- `arduino_uart`: `ARDUINO_UART_D0D1` or similar are available
- `arduino_spi`: `ARDUINO_SPI_ISP` or similar are available
- `arduino_i2c`: `ARDUINO_I2C_UNO` or similar are available
- mechanical/electrical compatibility with specific form factors
can now be expressed as features:
- `aruino_shield_nano`: Arduino NANO compatible headers
- `aruino_shield_uno`: Arduino UNO compatible headers
- `aruino_shield_mega`: Arduino MEGA compatible headers
- `aruino_shield_isp`: ISP header is available
This provides the groundwork to implement shield support as modules
that can rely on the I/O mappings, rather than having to provide a
configuration per board.
19718: drivers/dht: busy wait reimplementation r=benpicco a=hugueslarrive
### Contribution description
In PR #19674, I also provided quick and dirty fixes to restore functionality on esp8266 and enable operation on AVR. While reviewing PR #18591, it became apparent to me that this driver needed a refresh, particularly its migration to ztimer.
The cause of the malfunction on esp8266 was that since the default switch to ztimer as the backend for xtimer, XTIMER_BACKOFF was no longer taken into account. Therefore, the correction I provided in PR #19674 simply made explicit what was previously done implicitly with xtimer and now needs to be done explicitly with ztimer (spinning instead of sleeping).
Moreover, it was unnecessarily complex to measure the pulse duration in a busy-wait implementation, which required 2 calls to ztimer_now() and 32-bit operations expensive on 8-bit architecture. Instead, it is sufficient to read the state of the bus at the threshold moment.
Finally, in practice, it is possible to reduce the read interval (down to less than 0.5s for DHT22) by "harassing" the DHT with start signals until it responds.
This re-implementation brings the following improvements:
- Many backports from `@maribu's` IRQ based implementation (#18591):
- Use of ztimer
- Use of errno.h
- Use of a dht_data structure to pass arguments, to facilitate integration
- Adaptation of the bit parsing technique to parse bits into the data array
- Reintroduction of DHT11/DHT22 differentiation.
- Separation of `dht_read()` steps into functions for better readability and the ability to share certain functions among different implementations
- Sensor presence check in `dht_init()`
- ~~Automatic adjustment to a minimum data hold time~~
- Default input mode changed to open drain (a pull-up resistor should be placed close to the output if necessary but not close to the input)
- AVR support without platform-specific handling by avoiding ztimer_spin() and using the overflow of an 8-bit variable as a pre-timeout to minimize time-consuming ztimer_now() calls
Regarding the changes in the start signal sequence and the removal of the `_reset()` function:
~~In the previous implementation, there was an unnecessary spike at the beginning of the signal sequence, corresponding to START_HIGH_TIME. This spike has been removed in the re-implementation, as it is unnecessary. Instead, the MCU now simply pulls the signal low for START_LOW_TIME and then releases the bus, which is sufficient for initiating communication with the DHT sensor.~~ Actually, it is necessary to raise the bus level; otherwise, the _wait_for_level() called immediately after to check the response of the DHT may read the port before the signal level is raised, resulting in a false positive.
Additionally, the previous implementation had an issue where the MCU switched back to output mode and went high immediately after reading the 40 bits of data. However, the DHT sensor was still transmitting 2 or 3 additional bytes of '0' at that point, causing a conflict. This issue has been resolved in the re-implementation:
~~Regarding the optimization for AVR, I have performed measurements of `_wait_for_level()` until timeout (85 loops):~~
~~- on esp8266-esp-12x: 264 µs, which is 3.11 µs per loop~~
~~- on nucleo-f303k8: 319 µs, which is 3.75 µs per loop~~
~~- on arduino-nano: 3608 µs, which is 42.45 µs per loop~~
~~Duration measurements on the Arduino Nano:~~
19737: dist/tools/openocd: start debug-server in background and wait r=benpicco a=fabian18
19746: buildsystem: Always expose CPU_RAM_BASE & SIZE flags r=benpicco a=Teufelchen1
### Contribution description
Hello 🐧
This moves the definition of `CPU_RAM_BASE/SIZE` from being only available in certain situation to be always available.
Reason for change is to simplify common code in the cpu folder.
In cooperation with `@benpicco`
### Testing procedure
Passing CI
### Issues/PRs references
First usage will be in the PMP driver. Although there is more code in RIOT that could be refactored to use these defines instead of hacks / hardcoded values.
Co-authored-by: Hugues Larrive <hlarrive@pm.me>
Co-authored-by: Fabian Hüßler <fabian.huessler@ml-pa.com>
Co-authored-by: Teufelchen1 <bennet.blischke@outlook.com>
RIOT supports two distinct families of the MSP430: The [MSP430 x1xx]
MCU family and the [MSP430 F2xx/G2xx] MCU family. For both incompatible
MCU families the code was located in the msp430fxyz folder, resulting
in case of the UART driver in particularly bizarre code looking roughly
like this:
#ifndef UART_USE_USCI
/* implementation of x1xx peripheral ... */
#else
/* implementation of F2xx/G2xx peripheral ... */
#endif
/* zero shared code between both variants */
This splits the peripheral drivers for USCI and USART serial IP blocks
into separate files and relocates everything in cpu/msp430, similar to
how cpu/stm32 is organized.
[MSP430 x1xx]: https://www.ti.com/lit/ug/slau049f/slau049f.pdf
[MSP430 F2xx/G2xx]: https://www.ti.com/lit/ug/slau144k/slau144k.pdf
Checking for overflow of integer addition by comparing against one of
the arguments of the addition does not work when the result of the
addition is automatically promoted to a larger type.
Fix by using an explicit cast to make sure that the result of the
addition is not implicitly converted to a larger type.
19212: shell/rtc: use rtc_tm_normalize() to sanitize input r=benpicco a=benpicco
19360: gcoap: make use coap_build_reply() in gcoap_resp_init() r=benpicco a=benpicco
19401: shell/cmds: add genfile command r=benpicco a=benpicco
19645: sys/isrpipe: Replace xtimer with ztimer_usec r=benpicco a=MrKevinWeiss
### Contribution description
Getting ready for the xtimer dep.
### Testing procedure
Green murdock, there is no explicit test for isrpipe but since it runs xtimer compat it should operate the same.
### Issues/PRs references
19720: tests: remove unnecessary use of floating point r=benpicco a=benpicco
Co-authored-by: Benjamin Valentin <benjamin.valentin@bht-berlin.de>
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Co-authored-by: MrKevinWeiss <weiss.kevin604@gmail.com>
Co-authored-by: Benjamin Valentin <benpicco@beuth-hochschule.de>
19693: sys/color: extend unittest and fix module r=maribu a=kfessel
### Contribution description
this extends the unittest for sys_color testing more colors
### Testing procedure
```
RIOT_tree/tests/unittests$ make tests-color test
```
will fail since our `rgb2hsv` implementation is wrong (or is using an other colorspace than hsv2rgb (without documenting))
the new `hsv2rgb` test will succeed
### Issues/PRs references
#19614 was the reason i had a look at this
#1315 added the rgb2hsv and hsv2rgb function
#9940 added the test for black special case
https://www.vagrearg.org/content/hsvrgb << some optimization for that function (avoiding float)
Co-authored-by: Karl Fessel <karl.fessel@ovgu.de>
19686: sys/string_utils: add memchk() r=maribu a=benpicco
19687: tests/unittests: remove old workaround for SAML1X and gcc9.X bug r=maribu a=dylad
### Contribution description
This reverts #13462, this workaround is no longer needed with newer GCC version.
### Testing procedure
Try to compile tests/unittests for `saml11-xpro` or `saml10-xpro`
### Issues/PRs references
This is a revert of #13462.
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Co-authored-by: Dylan Laduranty <dylan.laduranty@mesotic.com>
19610: drivers/periph/rtc: improve doc on rtc_set_alarm r=maribu a=maribu
### Contribution description
- point out behavior on denormalized time stamps
- use errno codes to indicate errors (and adapt the few instances of actual error handling to use them)
19670: cpu/stm32: stm32f4 BRR from BSRR r=maribu a=kfessel
### Contribution description
sometimes one wants to save one instruction :)
just write the bits we need to write.
### Testing procedure
tests/periph/gpio_ll tests this
### Issues/PRs references
`@maribu` might know some reference
maybe #19407
19678: gnrc_sixlowpan_iphc: fix NULL pointer dereference r=maribu a=miri64
19679: gnrc_sixlowpan_frag_sfr: fix ARQ scheduler race-condition r=maribu a=miri64
19680: gnrc_sixlowpan_frag_rb: fix OOB write in _rbuf_add r=maribu a=miri64
19681: sys/xtimer: improve documentation r=maribu a=maribu
### Contribution description
- Add a warning that xtimer is deprecated, so that new code hopefully starts using ztimer
- Add a hint that `ztimer_xtimer_compat` can be used even after `xtimer` is gone
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Co-authored-by: Karl Fessel <karl.fessel@ovgu.de>
Co-authored-by: Martine Lenders <m.lenders@fu-berlin.de>
- Add a deprecation note to xtimer, so that new code hopefully
starts using ztimer
- Add a hint that `ztimer_xtimer_compat` can be used even after `xtimer`
is gone
19268: shell_lock: don't set CONFIG_SHELL_SHUTDOWN_ON_EXIT r=benpicco a=benpicco
Co-authored-by: Benjamin Valentin <benpicco@beuth-hochschule.de>
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
19601: SUIT: Prepared manifests r=chrysn a=chrysn
### Contribution description
While SUIT can generally be used already with manifests that are "dropped into memory" (by any mechanism), the convenient SUIT worker thread mechanism so far could not be used with it.
This adds the suit_worker_try_prepare / suit_worker_trigger_prepared
pair for using the SUIT worker, and breaks suit_handle_manifest_buf out
of suit_handle_url (where the latter now calls the former).
#### By-catch
As part of factoring out reaping of the zombie worker thread, a locking
error that deadlocks the SUIT worker in case the race between the mutex
being unlocked and the thread being reaped hits the necessary handling
code is fixed (and mutex_unlock is called in the error path).
### Testing procedure
SUIT tests should pass.
https://github.com/RIOT-OS/RIOT/pull/19659 provides a demo of how the new API is used.
### Issues/PRs references
I think that the currently employed mechanism of having a resource to which a URL with the manifest gets posted is contrary to the design goals of SUIT -- the signed manifest should be what justifies the device to spend resources (eg. get data from a server), not a URI that is just *not* signed.
This PR makes it easier to implement a resource to which the manifest can be POSTed, rather than a CoAP URI that represents the manifest, as is proposed (but not mature) in
https://github.com/RIOT-OS/RIOT/pull/19659.
[edit: Adjusted to reflect decisions made during review]
Co-authored-by: chrysn <chrysn@fsfe.org>
This adds the suit_worker_try_prepare / suit_worker_trigger_prepared
pair for using the SUIT worker, and breaks suit_handle_manifest_buf out
of suit_handle_url (where the latter now calls the former).
As part of factoring out reaping of the zombie worker thread, a locking
error that deadlocks the SUIT worker in case the race between the mutex
being unlocked and the thread being reaped hits the necessary handling
code is fixed (and mutex_unlock is called in the error path).
