There are new pseudomodules for this driver:
- atwinc15x0_static_connect: Should behave as before, by trying to connect to an AP
by specified WIFI_SSIS and WIFI_PASS
- atwinc15x0_dynamic_connect: takes connection request via NETOPT_CONNECT
and provides the connection result via callback
- atwinc15x0_dynamic_scan: takes network scan requests via NETOPT_SCAN
and provides the scan result as a sorted list via callback
19764: drivers/shield_w5100: add module for the W5100 Ethernet Shield r=benpicco a=maribu
### Contribution description
This module provides no more than the correct configuration parameters for the `w5100` driver using the Arduino I/O mapping features. But by doing so, it will work out of the box with every mechanically and electrically compatible board for which the Arduino I/O mapping features are implemented.
19781: cpu/nrf{53,9160}: add pwm support r=benpicco a=dylad
### Contribution description
This PR moves the nRF52 PWM driver to `cpu/nrf5x_common` to allow nRF9160 and nRF53 to use this driver.
IP is identical on these families.
I didn't test on nRF9160DK and I didn't test if there is any regression on nRF52-based board as I don't have any so tests are welcome !
However it works fine on nRF53-based board.
### Testing procedure
Flash the `tests/periph/pwm` test application on `nrf5340dk` or `nrf9160dk`.
You can then use the `osci` command to make the onboard LEDs "breath".
You can also attach an oscilloscope and/or logic analyzer to watch the signal.
### Issues/PRs references
~~Based on #19769~~
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@posteo.net>
Co-authored-by: Dylan Laduranty <dylan.laduranty@mesotic.com>
Co-authored-by: dylad <dylan.laduranty@mesotic.com>
This module provides no more than the correct configuration parameters
for the `w5100` driver using the Arduino I/O mapping features. But
by doing so, it will work out of the box with every mechanically and
electrically compatible board for which the Arduino I/O mapping
features are implemented.
19712: cpu/riscv: Add PMP driver r=MrKevinWeiss a=Teufelchen1
### Contribution description
Hi! 🐘
this adds a basic RISC-V physical memory protection (PMP) driver to RIOT. Well, 'driver' might be a stretched, feels more like a little utility :)
EDIT: Also added a no-execute RAM option for the hifive & a corresponding test
Since I only have an Hifive rev b, it's only enabled on this board / cpu. I also tested the code on an ESP32-C but the feature can't be enabled there, as `cpu/riscv_common/` is not used by the ESP32...
### Testing procedure
* Grab a hifive rev b
* go to `examples/hello-world`
* Add `USEMODULES += periph_pmp` to the `Makefile`
* Include `pmp.h` in `main.c`
* Add code e.g. `print_pmpcfg(0);`
* compile & flash & term
You should see something like this:
```
# Hello World!
# You are running RIOT on a(n) hifive1b board.
# This board features a(n) fe310 MCU.
# pmp00cfg: - R-X OFF 0x00000000 - 0x00000000
```
Co-authored-by: Teufelchen1 <bennet.blischke@outlook.com>
This allows using the arduino_pwm feature (which is translated into a
module) without the arduino module; e.g. for only using the Arduino
I/O mapping but not the Arduino API.
The coreclk shell command now prints the CPU frequency in Hz, which
can be useful for boards with RC generated CPU frequency (e.g.
RP2040, FE310, or MPS430Fx1xx MCUs allow this) which may quite a bit
off the target frequency.
This commit adds support for URBs (USB Request/Response Blocks). These
allow for submitting multi-transfer sized buffers with USBUS handling
the individual usbdev xmits. Multiple URBs can be queued at once for a
single endpoint and USBUS will handle them in the order of submission.
OUT endpoint URBs must always consist of a whole number of full-sized
transfers (N x MaxEndpointSize). They will automatically finish after
the endpoint received a transfer less than the endpoint size.
IN endpoints can be arbitrary-sized and do not have to consist of a
whole number of full-sized transmissions. They support a flag to
indicate that the last transfer in the sequence must be less than a full
sized transfer (USBUS_URB_FLAG_AUTO_ZLP) and this adds a zero length
transfer at the end of the transmissions if the last transfer was equal
to the maximum transfer size.
URBs can be cancelled, but if the URB is already being processed it will
be cancelled after the current transmission within the URB is finished.
If it is still in the queue it will immediately be removed from the
queue.
18682: pkg/lwext4: add lightweight implementation of the ext2/3/4 filesystem r=benpicco a=benpicco
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
The previous servo driver didn't provide any benefit over using PWM
directly, as users controlled the servo in terms of PWM duty cycles.
This changes the interface to provide a high level interface that
abstracts the gory PWM details.
In addition, a SAUL layer and auto-initialization is provided.
Co-authored-by: benpicco <benpicco@googlemail.com>
Hooking into the existing wrappers for `malloc()`, `calloc()`,
`realloc()`, and `free()`, the new (pseudo) module `malloc_tracing`
prints out the calls to the given functions, the program counter of
the caller, as well as the return result.
The intent is to aid debugging double-frees, invalid frees, or memory
leaks.
Add USE_MODULE += "stdio_uart_onlcr" to enable it.
This is named after the "onlcr" stty flag, which does the same thing.
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
