7d0c475113
Merge pull request #13486 from bergzand/pr/suit/ietf_v3
...
SUIT: Update to draft-ietf-v3
2020-03-20 14:44:29 +01:00
Francisco
cdbf0b2d69
Merge pull request #13583 from benpicco/at86rf215-minimal
...
drivers/at86rf215: add basic support for AT86RF215 dual-band radio
2020-03-20 09:33:50 +01:00
413b91326f
tests/suit_v3_manifest: Add draft-ietf-v3 manifest parser test
...
Co-authored-by: Kaspar Schleiser <kaspar@schleiser.de>
2020-03-19 22:56:01 +01:00
benpicco
b0fab9c53a
Merge pull request #13638 from gschorcht/sys/shell/rtt_command
...
sys/shell: add rtt command
2020-03-19 21:21:12 +01:00
Gunar Schorcht
3d20b0b6c5
sys/shell: add rtt command
2020-03-19 17:17:26 +01:00
521bb7e643
Merge pull request #11311 from benpicco/openocd-raspi
...
makefiles: add OpenOCD config for Raspberry Pi GPIO
2020-03-19 16:40:17 +01:00
Benjamin Valentin
d35511bee7
drivers/at86rf215: Add basic driver for the AT86RF215 radio
...
This adds a driver for the SPI based AT86RF215 transceiver.
The chip supports the IEEE Std 802.15.4-2015 and IEEE Std 802.15.4g-2012 standard.
This driver supports two versions of the chip:
- AT86RF215: dual sub-GHz & 2.4 GHz radio & baseband
- AT86RF215M: sub-GHz radio & baseband only
Both radios support the following PHY modes:
- MR-FSK
- MR-OFDM
- MR-O-QPKS
- O-QPSK (legacy)
The driver currently only implements support for legacy O-QPSK.
To use both interfaces, add
GNRC_NETIF_NUMOF := 2
to your Makefile.
The transceiver is able to send frames of up to 2047 bytes according to
IEEE 802.15.4g-2012 when operating in non-legacy mode.
Known issues:
- [ ] dBm setting values are bogus
- [ ] Channel spacing for sub-GHz MR-O-QPSK might be wrong
- [ ] TX/RX stress test will lock up the driver on openmote-b
2020-03-19 14:39:18 +01:00
Francisco Molina
9536a80e52
Makefile.dep: use stdio.inc.mk
...
Move all stdio dependencies to its own makefile
2020-03-18 15:58:38 +01:00
14bdf8f46b
sys/suit: Add SUIT draft ietf-v3 firmware upgrade module
...
Co-authored-by: Kaspar Schleiser <kaspar@schleiser.de>
2020-03-18 14:13:12 +01:00
accbfbd0d1
tools/bossa: add and configure preflash-delay when required
2020-03-18 10:43:05 +01:00
Francisco Molina
a31003a23c
tests: add interactive_sync adapted to shell
2020-03-17 17:23:27 +01:00
benpicco
a0cc4b0515
Merge pull request #13623 from Scallog/add_rom_offset_stm32
...
makefiles/boards/stm32.ink.mk: Use ROM_OFFSET with stm32flash
2020-03-16 12:09:40 +01:00
Corentin 'Kmikaz' Vigourt
6a559f1924
makefiles/boards/stm32.ink.mk: Use ROM_OFFSET with stm32flash
2020-03-16 10:47:32 +01:00
benpicco
db2ee4cbf6
Merge pull request #13634 from fjmolinas/pr_cc2538_flasher_guard
...
makefiles/tools/cc2538-bsl.inc.mk: allow FLASHER override
2020-03-16 00:58:37 +01:00
Francisco Molina
a00d61a2d6
makefiles/tools/cc2538-bsl.inc.mk: allow FLASHER override
...
If flasher is changed then make will still see it as a FLASH
dependency and try to execute the target which will likely not
exist.
A use case for this is when flashing on a remote machine and setting
FLASHER=ssh to then execute the FLASHER on the remote.
2020-03-15 11:58:39 +01:00
Robert Hartung
dc6665d5cf
Merge pull request #12717 from dylad/pr/bme680_pkg_driver
...
driver/bme680: add I2C/SPI driver for BME680 device
2020-03-12 14:00:40 +01:00
Francisco
3153a86551
Merge pull request #11192 from aabadie/pr/tools/dfu
...
boards: include common dfu logic where applicable
2020-03-12 09:05:32 +01:00
Gunar Schorcht
9dd11eb188
drivers: add support for BME680 driver
...
Add the support for BME680 based on the BME680 vendor driver package.
2020-03-12 08:42:59 +01:00
benpicco
52cc02c9a9
Merge pull request #13387 from nmeum/mpu_noexec_ram_ng
...
Add optional support for executable space protections
2020-03-11 20:00:44 +01:00
1e8037670b
Merge pull request #10420 from gschorcht/drivers_apds99xx
...
drivers: add driver for APDS99XX ambient light and proximity sensors
2020-03-11 16:27:53 +01:00
Schorcht
7548a6e849
drivers: add APDS99XX ALS and proximity
2020-03-11 14:21:47 +01:00
benpicco
008faef16a
Merge pull request #13581 from Scallog/olimexino-stm32-support
...
boards/olimexino-stm32: add support for olimexino-stm32 board
2020-03-11 11:40:53 +01:00
benpicco
d294e1d01c
Merge pull request #9572 from maribu/atmega-debug
...
On-Chip Debugging for AVR/ATmega based boards
2020-03-11 11:40:40 +01:00
Corentin 'Kmikaz' Vigourt
a4976c3333
makefiles/boards/stm32.inc.mk: add stm32flash support
2020-03-11 11:00:49 +01:00
6560a1f567
makefiles/jlink: export JLINK_PRE_FLASH to flash targets
2020-03-10 16:31:30 +01:00
5458f4d400
makefiles/jlink: export JLINK_RESET_FILE to required targets
2020-03-10 16:30:37 +01:00
04d32e9609
makefiles/jlink: export JLINK_IF to required targets
2020-03-10 16:29:02 +01:00
40e754c9d8
makefiles/jlink: only export JLINK_DEVICE when required
2020-03-10 16:28:03 +01:00
Francisco
6ba665858b
Merge pull request #13593 from aabadie/pr/boards/pyocd_export_remove
...
boards/pyocd: cleanup use of `export` keyword
2020-03-10 15:19:34 +01:00
Marian Buschsieweke
f2edcf9674
makefiles/tools/avrdude: Improved debug handling
...
- Choose correct debug protocol for ATmega328P (which supports debugWIRE instead
of JTAG)
- Allow overwriting debugger device via AVR_DEBUGDEVICE environment variable,
default to the Atmel-ICE (least expensive, supports most AVR devices)
2020-03-10 14:03:33 +01:00
Marian Buschsieweke
edd93411fe
dist: De-duplicated AVR debug config & scripts
...
Use common debug.sh, debug_srv.sh and gdb.conf for all AVR boards.
2020-03-10 12:54:51 +01:00
f56470925b
boards: include common dfu logic where applicable
2020-03-10 11:42:10 +01:00
23a3dcf828
makefiles/dfu: refactor configuration file
2020-03-10 11:42:10 +01:00
660b11261d
makefiles/dfu: remove unapplicable variables
2020-03-10 11:01:43 +01:00
benpicco
6f7293d7c3
Merge pull request #13559 from aabadie/pr/sys/crypto_modules_rework
...
sys/crypto: define cipher using a module instead of CFLAGS
2020-03-09 19:41:27 +01:00
Benjamin Valentin
74251383a0
makefiles: add OpenOCD config for Raspberry Pi GPIO
...
OpenOCD supports bit-banging the GPIOs of the Raspberry PI to emulate
an SWD flasher.
Add a raspi.inc.mk to support that option.
2020-03-09 19:12:40 +01:00
a83510c354
makefiles: add common file for cc2538-bsl flasher
2020-03-09 18:17:37 +01:00
fb27409b73
makefiles/pyocd: only export PYOCD_ADAPTER_INIT when required
2020-03-08 15:12:44 +01:00
2977b06a8d
makefiles/pyocd: only export FLASH_TARGET_TYPE when required
2020-03-08 15:12:44 +01:00
Sören Tempel
2c1a627118
Add mpu_noexec_ram pseudomodule
2020-03-07 13:09:55 +01:00
f6c4e269b1
sys/crypto: define ciphers via pseudomodules
2020-03-06 19:49:58 +01:00
benpicco
dbe1270f66
Merge pull request #13568 from benpicco/cc2538-bsl.py-upstream
...
dist/tools/cc2538-bsl: use upstream version
2020-03-06 14:08:09 +01:00
benpicco
7877ffdf2a
Merge pull request #13511 from fjmolinas/pr_auto_init_periph
...
drivers/periph_common: add periph_init% modules
2020-03-06 13:05:57 +01:00
Francisco Molina
6b6479e6e9
drivers/periph_common: add periph_init% module
2020-03-06 11:21:19 +01:00
Benjamin Valentin
ed4d871835
dist/tools/cc2538-bsl: use upstream version
...
Automatically fetch the upstream version of cc2538-bsl.py instead
of maintaining our own fork of the tool.
fixes #13566
2020-03-06 11:13:21 +01:00
ed316309c8
Merge pull request #11874 from kaspar030/ztimer
...
sys/ztimer: initial import
2020-03-06 09:46:27 +01:00
Martine Lenders
ff425576a0
slipdev_stdio: provide stdio multiplexing over SLIP
2020-03-06 08:58:45 +01:00
benpicco
7af046d740
Merge pull request #13548 from benpicco/sys/auto_init/netif-manual
...
sys/auto_init: allow delayed initialisation of SAUL & gnrc_netif
2020-03-05 17:05:02 +01:00
Jan Mohr
aa5ffe5a6d
drivers/lis2dh12: added interrupt function
2020-03-04 17:01:58 +01:00
Benjamin Valentin
521b1ce440
sys/auto_init: allow delayed initialisation of SAUL
...
Co-authored-by: Martine S. Lenders <m.lenders@fu-berlin.de>
2020-03-04 16:13:40 +01:00
