This commit changes the name of the requests over the control endpoints
to control requests instead of setup requests. This is a terminology fix
to follow the USB specification more closely as technically only the
first stage of a control request is named setup which contains a setup
packet. The whole transfer is a control transfer.
This enables 'pthread' support on arduino.
avr-libc C90 'time.h' does not include 'sys/types.h' as POSIX expects it.
However, the type previously defined conflicts with the one in
'cpu/atmega_common/avr_libc_extra/include/sys/types.h' when both are
included, so include 'sys/types.h'.
Maybe it should alway be included by 'time.h' but this
would need its specific review.
llvm-ar behaves weidly when creating thin archive. This only manifests
itself when using arduino sketches as these are built from the "bin"
directory.
Specifically, given a directory "m" and an object in "m/obj.o " an
invocation with CWD==m:
```
llvm-ar rcTs ../m.a obj.o
```
Will create a maformed archive. Binutils does not have any issue with this.
The following command, executed with CWD==m/.. works:
```
llvm-ar rcTs m.a m/obj.o
```
The trick used in this commit is to put the source files in a different
directory than the object files and compile from there.
- add init_schedstatistics function to be called after
auto_init, that way xtimer_is init is called before
the first call to xtimer_now
- register schedstatics code as a callback to be executed
on each sched_run()
- Removed stdio_init() from newlib's _init(), as this is too late in the boot
process to allow DEBUG()ing during periph_init()
- Added stdio_init() to the various cpu_init() routines of the ARM CPUs just
before periph_init()
The function insert returns KERNEL_PID_UNDEF now because pthread_create checks for it.
In pthread_create it checks now if thread_create returns a valid pid
before this commit the src address was checked for multicast, but the dst address should be checked. Therefore udp multicast packets would be flooded back to the src as ICMPv6 error, as not all nodes had a UDP receiver registered.
- Serial.print() and Serial.println() have been extended to support:
- unsigned int
- long
- unsigned long
- The SerialFormat BIN has been implemented
- Serial.println(void) has been added
Rename TMP006 to TMP00x
Add TMP007 sensor support to TMP00X
Change uint8_t reg to uint16_t
Add to doxygen documentation group
Expose compile time configurations
Move defines from .c to .h
Change double to float, because double is not needed
Add TMP007 register information
Generate a module for arduino sketches in a subfolder of BINDIR.
This prevents issues when doing concurrent builds or out of tree build with
readonly sources.
Declare all generated files as `BUILDDEPS` to be re-created after
`clean` on parrallel `clean all`.
When a keepalive timeout occurs keepalive_retry_cnt remains zero,
so when the connection is re-established _on_keepalive_evt will
immediately disconnect instead of actually sending a keepalive ping.
The sequence looks like:
1. _on_connack: start con->keepalive_timer
2. Server does not respond to keepalive pings
3. _on_keepalive_evt: con->keepalive_retry_cnt reaches zero
4. Connection torn down and ASYMCUTE_DISCONNECTED sent to application
5. Application starts reconnection
6. _on_connack: start con->keepalive_timer again
7. First _on_keepalive_evt: con->keepalive_retry_cnt is still zero
8. Repeat from 4.
So this simply resets keepalive_retry_cnt in _on_connack when
the keepalive timer is restarted. It's a new connection, so
resetting the keepalive retry counter make senses regardless.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
With the increase of the message queue size from 8 to 16 in
946b06e4f0, the default stack became too small.
This changes the stack size to grow with the message queue size.
The cc110x driver has been re-written from scratch to overcome the limitations
of the old driver. The main motivation of the rewrite was to achieve better
maintainability by a detailed documentation, reduce the complexity and the
overhead of the SPI communication with the device, and to allow to
simultaneously use transceivers with different configuration regarding the used
base band, the channel bandwidth, the modulation rate, and the channel map.
Features of this driver include:
- Support for the CC1100, CC1101, and the CC1100e sub-gigahertz transceivers.
- Detailed documentation of every aspect of this driver.
- An easy to use configuration API that allows setting the transceiver
configuration (modulation rate, channel bandwidth, base frequency) and the
channel map.
- Fast channel hopping by pre-calibration of the channels during device
configuration (so that no calibration is needed during hopping).
- Simplified SPI communication: Only during start-up the MCU has to wait
for the transceiver to be ready (for the power regulators and the crystal
to stabilize). The old driver did this for every SPI transfer, which
resulted in complex communication code. This driver will wait on start up
for the transceiver to power up and then use RIOT's SPI API like every other
driver. (Not only the data sheet states that this is fine, it also proved to
be reliable in practise.)
- Greatly reduced latency: The RTT on the old driver (@150 kbps data rate) was
about 16ms, the new driver (@250 kbps data rate) has as RTT of ~3ms
(depending on SPI clock and on CPU performance) (measured with ping6).
- Increased reliability: The preamble size and the sync word size have been
doubled compared to the old driver (preamble: 8 bytes instead of 4,
sync word: 4 byte instead of 2). The new values are the once recommended by
the data sheet for reliable communication.
- Basic diagnostic during driver initialization to detect common issues as
SPI communication issues and GDO pin configuration/wiring issues.
- TX power configuration with netdev_driver_t::set() API-integration
- Calls to netdev_driver_t::send() block until the transmission has completed
to ease the use of the API (implemented without busy waiting, so that the
MCU can enter lower power states or other threads can be executed).
