Skald is a very small and simple, TX-only BLE stack that supports
sending advertisements only. It is useful for building all kinds
of BLE beacons with very minimal memory footprints.
If the payload length is zero and the next header field is not set to
NONXT, GNRC will interpret the current header as the payload because the
first snip is always interpreted as the payload. This can lead to loops
and or crashes.
When the payload length of an encapsulated IPv6 packet is 0, the
`_receive` function of IPv6 can be given a NULL pointer, causing the
IPv6 header checker to crash because of a NULL pointer dereference.
With the previous fix, we only have to register addresses that are not
VALID yet on reception of router advertisements. This removes the need
for the hacky `GNRC_NETIF_FLAGS_6LO_ADDRS_REG` flag that was only
introduced to prevent unnecessary re-registration.
The whole address registration looses its point if all addresses are
marked valid from the get-go. With this fix non-link-local addresses
are first marked TENTATIVE and only after successful registration
marked as VALID. Link-local addresses are assumed to always be VALID.
gnrc_sock currently does not compile with `gnrc_neterr` included, since
both `msg_try_receive()` and `msg_try_send()` expect a *pointer* to a
`msg_t`, not a `msg_t`.
To test, just compile an application using `gnrc_sock` (e.g.
`examples/gcoap`) with `USEMODULE+=gnrc_neterr`.
[RFC6775] only talks of *routers* processing router advertisements,
with regards of discarding them if they do not contain an ABRO.
Additionally, this change makes configuration of tests setups a lot
easier, where one note is a router distributing a prefix and the other
is a host to be configured with the RA. Just do the following on the
router:
```
> ifconfig <if> add <GUA>
> ifconfig <if> rtr_adv
```
e voilà! In current master both nodes would have needed to be compiled
with `GNRC_IPV6_NIB_CONF_MULTIHOP_P6C=0`.
[RFC6775]: https://tools.ietf.org/html/rfc6775#section-8.1.3
According to RFC 6724 ch. 5 rule 8, the source address candidate with
the longest matching prefix has to be selected. The current
implementation discards source addresses that have no matching prefix
(`match = 0`) which is perfectly fine for any global address.
At the moment ping is crashing if one pings the loopback address.
This was caused in #8214 when we moved interfaces from `kernel_pid_t`
ID to pointer-based handling, since loopback doesn't evaluate to such
an interface.
This fix
* assures that the periodicity of the final router advertisements is
kept (so that no administrative change e.g. adding prefixes to the
prefix list causes additional RAs outside the rate limitation)
* removes all administrative options (PIO, ABRO, 6CO) from final router
advertisements (with router lifetime == 0)
Adds a `nrfmin` case to IID generation, so an IID can be generated
from a `nrfmin` device's (short) address (the long address is just
4-time repetition of the short address).
Moves setting of addresses of length lesser than 3 to a function that
initializes the first 5 byte of the IID with `00:00:00:ff:fe` and then
fills up the rest with zeroes and the given short address.
I applied the following terminology and changed the wording in the doc
accordingly:
* must not: If the parameter is of the value it *must not* be it either
hits an assert or crashes the system.
* may not: The value can be that value, but the function will return an
error.
This renames the following functions
* `gnrc_netif_ipv6_addr_add()`
* `gnrc_netif_ipv6_addr_remove()`
* `gnrc_netif_ipv6_group_join()`
* `gnrc_netif_ipv6_group_leave()`
by appending the suffix `_internal`.
\## Reasoning
I'd like to provide a helper function for the *public* equivalent using
`gnrc_netapi_set()`, and those names are to nice to not be taken for
those.
\## Procedure
I used a combination of `git grep` and `sed` to do this and fixed the
alignment in the result of some cases by hand.
```sh
git grep --name-only "\<gnrc_netif_ipv6_\(addr\|group\)_\(add\|remove\|join\|leave\)\>" | \
xargs sed -i 's/\<gnrc_netif_ipv6_\(addr\|group\)_\(add\|remove\|join\|leave\)/\0_internal/g'
```
