17091: USBUS: Add URB support r=benpicco a=bergzand
### Contribution description
This commit adds support for URBs (USB Request/Response Blocks). These
allow for submitting multi-transfer sized buffers with USBUS handling
the individual usbdev xmits. Multiple URBs can be queued at once for a
single endpoint and USBUS will handle them in the order of submission.
OUT endpoint URBs must always consist of a whole number of full-sized
transfers (N x MaxEndpointSize). They will automatically finish after
the endpoint received a transfer less than the endpoint size.
IN endpoints can be arbitrary-sized and do not have to consist of a
whole number of full-sized transmissions. They support a flag to
indicate that the last transfer in the sequence must be less than a full
sized transfer (USBUS_URB_FLAG_AUTO_ZLP) and this adds a zero length
transfer at the end of the transmissions if the last transfer was equal
to the maximum transfer size.
URBs can be cancelled, but if the URB is already being processed it will
be cancelled after the current transmission within the URB is finished.
If it is still in the queue it will immediately be removed from the
queue.
### Testing procedure
- `tests/usbus_cdc_ecm` should still work. Testing one of the usbdev-supported platform should be sufficient here.
### Issues/PRs references
Needs #17064
18148: sys/flash_utils: helpers to store data in flash r=benpicco a=maribu
### Contribution description
This helpers that allow storing, accessing, and working with data in flash that works for both classical Harvard architectures (which do not map flash also into the address space) as well as modern Harvard architectures and von-Neumann architectures.
With this, `examples/default` again runs on the Arduino Uno / Nano. Since this board is still the "entry kit" for many people to embedded hardware, it would be nice to support it with our default example.
### Testing procedure
`examples/default` should run and work on ATmega boards (especially ATmega328P and ATmega32U4 based boards) as well on all other boards now.
### Issues/PRs references
None
Co-authored-by: Koen Zandberg <koen@bergzand.net>
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
This adds a layer of convenience abstraction over classical Harvard
architectures (like most AVRs) that do not map the flash memory into
the data address space and modern Harvard architectures or von-Neumann
architectures that do so. The motivation is to safe a lot of RAM for
AVR by storing constant strings into flash.
This commit adds support for URBs (USB Request/Response Blocks). These
allow for submitting multi-transfer sized buffers with USBUS handling
the individual usbdev xmits. Multiple URBs can be queued at once for a
single endpoint and USBUS will handle them in the order of submission.
OUT endpoint URBs must always consist of a whole number of full-sized
transfers (N x MaxEndpointSize). They will automatically finish after
the endpoint received a transfer less than the endpoint size.
IN endpoints can be arbitrary-sized and do not have to consist of a
whole number of full-sized transmissions. They support a flag to
indicate that the last transfer in the sequence must be less than a full
sized transfer (USBUS_URB_FLAG_AUTO_ZLP) and this adds a zero length
transfer at the end of the transmissions if the last transfer was equal
to the maximum transfer size.
URBs can be cancelled, but if the URB is already being processed it will
be cancelled after the current transmission within the URB is finished.
If it is still in the queue it will immediately be removed from the
queue.
18682: pkg/lwext4: add lightweight implementation of the ext2/3/4 filesystem r=benpicco a=benpicco
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
19292: sys/phydat: Fix unit confusion r=miri64 a=maribu
### Contribution description
Previously, `UNIT_G` was used for g-force with the correct symbol `g`, `UNIT_GR` for gram (as in kilogram) with the incorrect symbol `G` (which would be correct for Gauss), and `UNIT_GS` for Gauss with symbol `Gs` (which is an alternative correct symbol).
To avoid confusion between G-Force, Gauss, and Gram the units have been renamed to `UNIT_G_FORCE`, `UNIT_GRAM`, and `UNIT_GAUSS`. In addition, gram now uses the correct symbol `g`; which sadly is the same as for g-force. But usually there is enough context to tell them apart.
### Testing procedure
Green CI
### Issues/PRs references
None
19307: nanocoap_link_format: fix off-by-one error r=miri64 a=benpicco
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Co-authored-by: Benjamin Valentin <benpicco@beuth-hochschule.de>
18746: sys/clif: Fixing out of bounds read under certain conditions r=maribu a=Teufelchen1
Hi 😈
This fixes a potential out of bounds read in clif_encode_link. There is no code in RIOT that can be exploited.
The fix does not break the current API but alters the behaviour slightly. Before the change, the length attributes of `clif_attr_t` where optional. If missing, the length was deduced using `strlen()`. This fix makes those parameters required and if they are `0` it operates as if the length really is `0`. This might not be ideal but it is the only non api breaking fix I could think off.
```c
typedef struct {
char *value;
unsigned value_len; NO LONGER OPTIONAL
const char *key;
unsigned key_len; NO LONGER OPTIONAL
} clif_attr_t;
```
Depends on #18744
cc `@leandrolanzieri`
19161: bors.yaml: re-activate labels check + add block_labels r=miri64 a=miri64
Co-authored-by: Teufelchen1 <bennet.blischke@haw-hamburg.de>
Co-authored-by: Martine Lenders <m.lenders@fu-berlin.de>
Previously, `UNIT_G` was used for g-force with the correct symbol `g`,
`UNIT_GR` for gram (as in kilogram) with the incorrect symbol `G` (which
would be correct for Gauss), and `UNIT_GS` for Gauss with symbol `Gs`
(which is an uncommon but correct symbol).
To avoid confusion between G-Force, Gauss, and Gram the units have been
renamed to `UNIT_G_FORCE`, `UNIT_GRAM`, and `UNIT_GAUSS`. In addition,
gram now uses the correct symbol `g` and Gauss uses `G`.
19299: Add missing newline to output of telnet example r=benpicco a=Enoch247
### Contribution description
From the commit msg:
> The telnet example prints a line to the console, but it is not ended with a newline. When using pyterm, the last line is then never shown as it reads the console line by line and is waiting for the end of the line.
>
> This patch swaps use of `printf` for `puts` for the last line printed. This means the missing newline character gets added. This is also done to be consistent with the rest of the file, where puts is used whenever possible instead of printf.
### Testing procedure
1. `cd examples/telnet`
2. `make all flash term`
3. observe the final line "Local shell disabled" is printed, but would not have without this patch
### Issues/PRs references
- none known
19301: fib: document unused state r=benpicco a=benpicco
Co-authored-by: Joshua DeWeese <jdeweese@primecontrols.com>
Co-authored-by: Benjamin Valentin <benjamin.valentin@bht-berlin.de>
19294: sys/shell: don't include suit command by default r=benpicco a=benpicco
19295: gcoap: Finish the gcoap_get_resource_list_tl -> gcoap_get_resource_list renaming r=benpicco a=chrysn
### Contribution description
In #16688, an argument was added to the `gcoap_get_resource_list` function by creating a new function `gcoap_get_resource_list_tl` with a deprecation and roll-over plan.
This plan has not been acted on so far.
This PR shortens the original plan by just adding the argument to `gcoap_get_resource_list` and removing `gcoap_get_resource_list_tl` in a single go. The rationale for this deviation is that while it's a public API, its only two practical consumers are the (built-in) well-known/core implementation, and the (built-in) CoRE Resource Directory (cord) endpoint. Moreover, a further change to this API (switching over to `coap_block_slicer_t`) is expected to happen within this release cycle, which would take something like 4 total releases to get through otherwise, which is unrealistic for an API that there are no known external users of.
A second commit clean up ToDo items (in the changed function's documentation) that referred to a IETF draft that has long been abandoned by the CoRE WG.
### Testing procedure
Plain inspection and CI passing should suffice.
### AOB
There is a second analogous pair left over from #16688, `gcoap_req_send` / `gcoap_req_send_tl`. As that *is* expected to be used widely, I prefer not to mix these two concerns, and get the present one through without unnecessary hold-up.
Co-authored-by: Benjamin Valentin <benjamin.valentin@bht-berlin.de>
Co-authored-by: chrysn <chrysn@fsfe.org>
This is an API change in the latter, which would typically now take an
extra argument GCOAP_SOCKET_TYPE_UNDEF.
Follow-Up-For: https://github.com/RIOT-OS/RIOT/pull/16688
19278: gnrc_dhcpv6_client_simple_pd: select upstream based on type/index r=benpicco a=benpicco
19290: sys/crypto: make AES_KEY struct private & rename it r=benpicco a=benpicco
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Co-authored-by: Benjamin Valentin <benjamin.valentin@bht-berlin.de>
19142: sock_dtls: move common code into sock_dtls_establish_session() r=benpicco a=benpicco
Co-authored-by: Benjamin Valentin <benpicco@beuth-hochschule.de>
17045: sys/coding: add XOR based coding module r=benpicco a=benpicco
19243: cpu/gd32v: add periph_gpio_ll and periph_gpio_ll_irq support r=benpicco a=gschorcht
### Contribution description
This PR provides the `periph_gpio_ll` and `periph_gpio_ll_irq` support for GD32VF103. Level triggered interrupts are emulated.
`periph_gpio_ll_irq` could be split off from this PR as a separate PR if necessary.
### Testing procedure
Use any GD32V board and connect PA0 -> PB0 and PA1 -> PB1 where PA is the output port and PB the input port. With these connections `tests/periph_gpio_ll` should work.
```
BOARD=sipeed-longan-nano make -j8 -C tests/periph_gpio_ll flash term
```
If necessary, change the input and output pins by setting the environment variables and connect the corresponding pins, for example for `seeedstudio-gd32` PA1 -> PB8 and PA8 -> PB9:
```
PIN_OUT_0=1 PIN_OUT_1=8 PIN_IN_0=8 PIN_IN_1=9 BOARD=seedstudio-gd32 make -j8 -C tests/periph_gpio_ll flash term
```
### Issues/PRs references
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
This implements the XOR based error-correction code described by
Jürgen Fitschen (@jue89) at the RIOT Summit.
A parity byte is generated for each 3 payload bytes, then the payload array
is transposed by interpreting it as a 2D matrix with height of 3.
This is to reduce the chance of consecutive bytes ending up in the same
packet.
This allows to recover one in 3 lost data packets (if parity packets are received).
[0] https://summit.riot-os.org/2021/wp-content/uploads/sites/16/2021/09/s02-01.pdf
19178: nanocoap_sock: store message ID in nanocoap_sock_t r=benpicco a=benpicco
19186: cpu/gd32v: add periph_rtc support r=benpicco a=gschorcht
### Contribution description
This PR provides the `periph_rtc` support and is one of a bunch of follow up PRs that complete the peripheral drivers for GD32VF103.
### Testing procedure
`tests/periph_rtc` should work and should give the following output:
```
Help: Press s to start test, r to print it is ready
START
main(): This is RIOT! (Version: 2023.04-devel-144-gc17695-cpu/gd32v/periph_rtc)
RIOT RTC low-level driver test
This test will display 'Alarm!' every 2 seconds for 4 times
Setting clock to 2020-02-28 23:59:57
Clock value is now 2020-02-28 23:59:57
Setting alarm to 2020-02-28 23:59:59
Alarm is set to 2020-02-28 23:59:59
Alarm cleared at 2020-02-28 23:59:57
No alarm at 2020-02-28 23:59:59
Setting alarm to 2020-02-29 00:00:01
Alarm!
Alarm!
Alarm!
Alarm!
```
### Issues/PRs references
Co-authored-by: Benjamin Valentin <benjamin.valentin@bht-berlin.de>
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
18472: drivers/mrf24j40: add support for IEEE 802.15.4 Radio HAL r=benpicco a=jia200x
19175: drivers/periph_common/flashpage: fix silent error r=benpicco a=Enoch247
### Contribution description
This patch removes a test that silently hides failed writes to NULL. Instead, assert is used to ensure that the address is not NULL.
### Testing procedure
I am not certain how to update the tests to catch asserts. If this is possible, I will add a test, if someone will point me to a good example to learn from.
### Issues/PRs references
- none
Co-authored-by: Jose Alamos <jose@alamos.cc>
Co-authored-by: Joshua DeWeese <jdeweese@primecontrols.com>
19156: core/compiler_hints: add likely() / unlikely() hints r=kfessel a=benpicco
19174: tests/periph_spi clearly say when init succeeds r=benpicco a=jdavid
When the `tests/periph_spi` program succeeds the output can be interpreted as an error happened.
This PR makes it clearer when it does succeed.
### Contribution description
In `tests/periph_spi`:
- Explicitely say that the init operation was successful
- Rephrase the note to avoid misinterpretations
### Testing procedure
Run the `tests/periph_spi` program.
There is not much to test, just to verify the output, should be like this:
```
2023-01-19 10:42:33,768 # Trying to initialize SPI_DEV(1): mode: 0, clk: 0, cs_port: 0, cs_pin: 0
2023-01-19 10:42:33,777 # (if below the program crashes with a failed assertion, then it means the configuration is not supported)
2023-01-19 10:42:33,779 # Success.
```
### Issues/PRs references
Issue https://github.com/RIOT-OS/RIOT/issues/19025
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Co-authored-by: J. David Ibáñez <jdavid.ibp@gmail.com>
18477: gnrc_static: add static network configuration r=miri64 a=benpicco
19101: CI: update check-labels-action r=miri64 a=kaspar030
19155: Revert "sys/pm_layered: pm_(un)block add attribute optimize(3)" r=maribu a=Teufelchen1
Revert "sys/pm_layered: pm_(un)block add attribute optimize(3) -shortens hotpath"
This reverts commit 5447203921.
### Contribution description
Compiling `examples/gnrc_networking_mac` using `TOOLCHAIN=llvm` yields the following error:
```
RIOT/sys/pm_layered/pm.c:77:16: error: unknown attribute 'optimize' ignored [-Werror,-Wunknown-attributes]
__attribute__((optimize(3)))
```
As indicated, this is because the attribute `optimize` is GCC only and not present in LLVM.
Compare the manpages of [GCC](https://gcc.gnu.org/onlinedocs/gcc/Common-Function-Attributes.html) and [LLVM](https://clang.llvm.org/docs/AttributeReference.html).
### Testing procedure
Since this should only affect performance and not behavior, no special testing is needed. I am not aware of any tests in RIOT which could verify that assumption.
### Issues/PRs references
Introduced in #18846
There is another instance of this attribute being used in[ shell_lock.c](6fb340d654/sys/shell_lock/shell_lock.c (L80)). Since the usage is security related, I omit it from this PR.
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Co-authored-by: Kaspar Schleiser <kaspar@schleiser.de>
Co-authored-by: Teufelchen1 <bennet.blischke@haw-hamburg.de>
19057: fuzzing: Add uri_parser setup r=benpicco a=Teufelchen1
Hello!
### Contribution description
This PR is a replacement for PR #18802
In this contribution:
* The variable `AFL_FLAGS` is renamed to `FLAGS_FOR_AFL` because AFL is always complaining that `AFL_FLAGS` is not a valid env var for it. While this is not a bug nor an issue, I found it to be annoying.
* A generic input reader is added to simplify building a test harness
* The usage of this reader is demonstrated by adding a harness for fuzzing the uri_parser
(needs squashing after review)
### Testing procedure
Go to `fuzzing/uri_parser` and run `make all-asan` and `make fuzz` to get some action going.
Also mildly interesting: `./dist/tools/compile_test/compile_like_murdock.py -b native -a fuzzing/uri_parser`
### Issues/PRs references
The original PR #18802 is replaced because the generic input reader is present in both PRs but this PoC harness is much simpler.
19151: examples/gcoap: Fix shell parameter validation r=benpicco a=maribu
### Contribution description
Executing the shell command with an URI-Path that doesn't start with a slash results in an assertion error while composing the client side message. This is suboptimal user experience, so add an explicit check for a valid URI-Path and a dedicated error message.
### Testing procedure
#### In `master`
```
$ make BOARD=microbit-v2 -C examples/gcoap flash term
[...]
2023-01-15 22:23:32,512 # coap get [::1] /.well-known/core
2023-01-15 22:23:32,516 # gcoap_cli: sending msg ID 52272, 23 bytes
2023-01-15 22:23:32,520 # gcoap: response Success, code 2.05, 46 bytes
2023-01-15 22:23:32,524 # </cli/stats>;ct=0;rt="count";obs,</riot/board>
> coap get [::1] foo
2023-01-15 22:23:34,763 # coap get [::1] foo
2023-01-15 22:23:34,763 # 2329
2023-01-15 22:23:34,765 # *** RIOT kernel panic:
2023-01-15 22:23:34,767 # FAILED ASSERTION.
2023-01-15 22:23:34,767 #
2023-01-15 22:23:34,775 # pid | name | state Q | pri | stack ( used) ( free) | base addr | current
2023-01-15 22:23:34,784 # - | isr_stack | - - | - | 512 ( 200) ( 312) | 0x20000000 | 0x200001c8
2023-01-15 22:23:34,793 # 1 | main | running Q | 7 | 1536 ( 1072) ( 464) | 0x200006c0 | 0x2000095c
2023-01-15 22:23:34,802 # 2 | 6lo | bl rx _ | 3 | 1024 ( 328) ( 696) | 0x200036c0 | 0x200039c4
2023-01-15 22:23:34,810 # 3 | ipv6 | bl rx _ | 4 | 1024 ( 460) ( 564) | 0x20001294 | 0x20001574
2023-01-15 22:23:34,819 # 4 | udp | bl rx _ | 5 | 512 ( 300) ( 212) | 0x20003e98 | 0x20003f9c
2023-01-15 22:23:34,828 # 5 | coap | bl anyfl _ | 6 | 1112 ( 704) ( 408) | 0x20000e38 | 0x200011c4
2023-01-15 22:23:34,837 # 6 | nrf802154 | bl anyfl _ | 2 | 896 ( 288) ( 608) | 0x20001a90 | 0x20001d54
2023-01-15 22:23:34,843 # | SUM | | | 6616 ( 3352) ( 3264)
2023-01-15 22:23:34,843 #
2023-01-15 22:23:34,844 # *** halted.
2023-01-15 22:23:34,844 #
```
#### This PR
```
$ make BOARD=microbit-v2 -C examples/gcoap flash term
[...]
make: Entering directory '/home/maribu/Repos/software/RIOT/examples/gcoap'
/home/maribu/Repos/software/RIOT/dist/tools/pyterm/pyterm -p "/dev/ttyACM0" -b "115200"
2023-01-15 22:22:27,842 # Connect to serial port /dev/ttyACM0
Welcome to pyterm!
Type '/exit' to exit.
coap get [::1] /.well-known/core
2023-01-15 22:22:40,042 # coap get [::1] /.well-known/core
2023-01-15 22:22:40,046 # gcoap_cli: sending msg ID 25182, 23 bytes
2023-01-15 22:22:40,050 # gcoap: response Success, code 2.05, 46 bytes
2023-01-15 22:22:40,054 # </cli/stats>;ct=0;rt="count";obs,</riot/board>
> coap get [::1] foo
2023-01-15 22:22:43,858 # coap get [::1] foo
2023-01-15 22:22:43,862 # ERROR: URI-Path must start with a "/"
2023-01-15 22:22:43,866 # usage: coap <get|post|put|ping|proxy|info>
```
### Issues/PRs references
None
Co-authored-by: Teufelchen1 <bennet.blischke@haw-hamburg.de>
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
17066: sys/irq: Add C++ wrapper using RAII r=maribu a=jenswet
### Contribution description
This adds a C++ wrapper around the `irq.h` API. The wrapper uses RAII to accomplish a convenient and bug resistent use.
A little background: I'm currently writing my master thesis on using C++ for embedded development, at the working group that `@maribu` is part of. For that I will try to add better C++ support to several parts of RIOT and then do some benchmarking and metrics to compare it with the C implementation. For example, I also plan to add a wrapper around i2c, a std::cout drop-in replacement and probably some more about networks or threads.
### Testing procedure
I've added a unit test to verify that the IRQ wrapper calls the original `irq` functions as expected. As C++ and wrapper testing isn't done much so far in this project, I've added two additional headers to ease testing:
1. #17076 - fake functions framework, already merged
2. As there is no framework for C++ unit tests yet, I've added something for this too. Unfortunately the existing frameworks like GoogleTest, CppUTest or CppUnit don't easily compile for embedded or are difficult to integrate in to the RIOT build process. That's why I wrote some (simple) helper functions and macros inspired by the above frameworks. That allows to create C++ tests based on a fixture class with set up and tear down methods. It also allows some simple assertions and is easily extendable for other use cases. It wraps some of the fff functionality too.
Both of this is obviously not required for the initial reason of this PR. But I'd like to provide unit tests for the features that I suggest to introduce where possible. So I'd appreciate some feedback on that too. If you'd prefer a PR without or different tests please let me know.
You can run the test `irq_cpp` locally or on the CI to test the implementation.
Please feel free to give feedback or suggest improvements!
Co-authored-by: Jens Wetterich <jens@wetterich-net.de>
