diff --git a/boards/nucleo-l496zg/Kconfig b/boards/nucleo-l496zg/Kconfig
index 1b7b45d8d5..7f11eea9ab 100644
--- a/boards/nucleo-l496zg/Kconfig
+++ b/boards/nucleo-l496zg/Kconfig
@@ -15,6 +15,7 @@ config BOARD_NUCLEO_L496ZG
     select CPU_MODEL_STM32L496ZG
 
     # Put defined MCU peripherals here (in alphabetical order)
+    select HAS_PERIPH_ADC
     select HAS_PERIPH_I2C
     select HAS_PERIPH_LPUART
     select HAS_PERIPH_PWM
diff --git a/boards/nucleo-l496zg/Makefile.features b/boards/nucleo-l496zg/Makefile.features
index 5240bca884..892edb8f00 100644
--- a/boards/nucleo-l496zg/Makefile.features
+++ b/boards/nucleo-l496zg/Makefile.features
@@ -2,6 +2,7 @@ CPU = stm32
 CPU_MODEL = stm32l496zg
 
 # Put defined MCU peripherals here (in alphabetical order)
+FEATURES_PROVIDED += periph_adc
 FEATURES_PROVIDED += periph_i2c
 FEATURES_PROVIDED += periph_pwm
 FEATURES_PROVIDED += periph_rtc
diff --git a/boards/nucleo-l496zg/include/periph_conf.h b/boards/nucleo-l496zg/include/periph_conf.h
index 600725936a..dfc662888c 100644
--- a/boards/nucleo-l496zg/include/periph_conf.h
+++ b/boards/nucleo-l496zg/include/periph_conf.h
@@ -156,6 +156,57 @@ static const spi_conf_t spi_config[] = {
 #define SPI_NUMOF           ARRAY_SIZE(spi_config)
 /** @} */
 
+/**
+ * @brief ADC configuration
+ *
+ * Note that we do not configure all ADC channels,
+ * and not in the STM32L496ZG order.  Instead, we
+ * just define 6 ADC channels, for the Nucleo
+ * Arduino header pins A0-A5 and the internal VBAT channel.
+ *
+ * To find appropriate device and channel find in the
+ * board manual, table showing pin assignments and
+ * information about ADC - a text similar to ADC[X]_IN[Y],
+ * where:
+ * [X] - describes used device - indexed from 0,
+ * for example ADC1_IN10 is device 0,
+ * [Y] - describes used channel - indexed from 1,
+ * for example ADC1_IN10 is channel 10
+ *
+ * For Nucleo-L496ZG this information is in board manual,
+ * Table 11, page 38.
+ *
+ * @{
+ */
+static const adc_conf_t adc_config[] = {
+    { .pin = GPIO_PIN(PORT_A, 3), .dev = 0, .chan =  8 }, /* ADC12_IN8   */
+    { .pin = GPIO_PIN(PORT_C, 0), .dev = 0, .chan =  1 }, /* ADC123_IN1  */
+    { .pin = GPIO_PIN(PORT_C, 3), .dev = 0, .chan =  4 }, /* ADC123_IN4  */
+    { .pin = GPIO_PIN(PORT_C, 1), .dev = 0, .chan =  2 }, /* ADC123_IN2  */
+    { .pin = GPIO_PIN(PORT_C, 4), .dev = 0, .chan = 13 }, /* ADC12_IN13  */
+    { .pin = GPIO_PIN(PORT_C, 5), .dev = 0, .chan = 14 }, /* ADC12_IN14  */
+    /* VBAT is connected ADC1_IN18 or ADC3_IN18 and a voltage divider
+     * is used, so that only 1/3 of the actual VBAT is measured. This
+     * allows for a supply voltage higher than the reference voltage.
+     *
+     * For Nucleo-L496ZG more information is provided in MCU datasheet,
+       in section 3.17.3 - Vbat battery voltaga monioring, page 43.
+     */
+    { .pin = GPIO_UNDEF, .dev = 0, .chan = 18 },
+};
+
+/**
+ * @brief Number of ADC devices
+ */
+#define ADC_NUMOF           ARRAY_SIZE(adc_config)
+
+/**
+ * @brief VBAT ADC line
+ */
+#define VBAT_ADC            ADC_LINE(6)
+
+/** @} */
+
 #ifdef __cplusplus
 }
 #endif