boards/adafruit-pybadge: add support

boards/adafruit-pybadge/Kconfig

@@ -0,0 +1,32 @@
+# Copyright (c) 2020 Inria
+#
+# This file is subject to the terms and conditions of the GNU Lesser
+# General Public License v2.1. See the file LICENSE in the top level
+# directory for more details.
+
+config BOARD
+    default "adafruit-pybadge" if BOARD_ADAFRUIT_PYBADGE
+
+config BOARD_ADAFRUIT_PYBADGE
+    bool
+    default y
+    select CPU_MODEL_SAMD51J19A
+    select HAS_HIGHLEVEL_STDIO
+    select HAS_PERIPH_ADC
+    select HAS_PERIPH_DAC
+    select HAS_PERIPH_I2C
+    select HAS_PERIPH_PWM
+    select HAS_PERIPH_RTC
+    select HAS_PERIPH_RTT
+    select HAS_PERIPH_SPI
+    select HAS_PERIPH_TIMER
+    select HAS_PERIPH_UART
+    select HAS_PERIPH_USBDEV
+
+    # select HAVE_ST7735  # not supported yet
+    select HAVE_SAUL_GPIO
+    select HAVE_MTD_SPI_NOR
+    # This specific board requires SPI_ON_QSPI for the MTD_SPI_NOR
+    select MODULE_PERIPH_SPI_ON_QSPI if MODULE_MTD_SPI_NOR
+
+source "$(RIOTBOARD)/common/samdx1-arduino-bootloader/Kconfig"

boards/adafruit-pybadge/Makefile

@@ -0,0 +1,5 @@
+MODULE = board
+
+DIRS = $(RIOTBOARD)/common/samdx1-arduino-bootloader
+
+include $(RIOTBASE)/Makefile.base

boards/adafruit-pybadge/Makefile.dep

@@ -0,0 +1,16 @@
+ifneq (,$(filter saul_default,$(USEMODULE)))
+  USEMODULE += saul_gpio
+endif
+
+ifneq (,$(filter disp_dev,$(USEMODULE)))
+  # Driver not supported yet
+  # USEMODULE += st7735
+endif
+
+ifneq (,$(filter mtd,$(USEMODULE)))
+  FEATURES_REQUIRED += periph_spi_on_qspi
+  USEMODULE += mtd_spi_nor
+endif
+
+# setup the samd21 arduino bootloader related dependencies
+include $(RIOTBOARD)/common/samdx1-arduino-bootloader/Makefile.dep

boards/adafruit-pybadge/Makefile.features

@@ -0,0 +1,21 @@
+CPU = samd5x
+CPU_MODEL = samd51j19a
+
+# Put defined MCU peripherals here (in alphabetical order)
+FEATURES_PROVIDED += highlevel_stdio
+FEATURES_PROVIDED += periph_adc
+FEATURES_PROVIDED += periph_dac
+FEATURES_PROVIDED += periph_i2c
+FEATURES_PROVIDED += periph_pwm
+FEATURES_PROVIDED += periph_rtc
+FEATURES_PROVIDED += periph_rtt
+FEATURES_PROVIDED += periph_spi
+FEATURES_PROVIDED += periph_timer
+FEATURES_PROVIDED += periph_uart
+FEATURES_PROVIDED += periph_usbdev
+
+# This configuration enables modules that are only available when using Kconfig
+# module modelling
+ifeq (1, $(TEST_KCONFIG))
+  KCONFIG_ADD_CONFIG += $(RIOTBOARD)/common/samdx1-arduino-bootloader/samdx1-arduino-bootloader.config
+endif

boards/adafruit-pybadge/Makefile.include

@@ -0,0 +1,9 @@
+CFLAGS += -DBOOTLOADER_UF2
+
+# stdio over usb takes several seconds to be up after flashing
+TERM_DELAY ?= 4
+
+# Include all definitions for flashing with bossa other USB
+include $(RIOTBOARD)/common/samdx1-arduino-bootloader/Makefile.include
+# Include handling of serial and non-bossa programmers (if selected by user)
+include $(RIOTMAKE)/boards/sam0.inc.mk

boards/adafruit-pybadge/board.c

@@ -0,0 +1,71 @@
+/*
+ * Copyright (C) 2020 Inria
+ *
+ * This file is subject to the terms and conditions of the GNU Lesser
+ * General Public License v2.1. See the file LICENSE in the top level
+ * directory for more details.
+ */
+
+/**
+ * @ingroup     boards_adafruit-pybadge
+ * @{
+ *
+ * @file
+ * @brief       Board initialization for the Adafruit PyBadge
+ *
+ * @author      Alexandre Abadie <alexandre.abadie@inria.fr>
+ *
+ * @}
+ */
+
+#include "cpu.h"
+#include "board.h"
+#include "mtd_spi_nor.h"
+#include "timex.h"
+
+#include "periph/gpio.h"
+
+#if IS_USED(MODULE_MTD)
+/* GD25Q16C */
+static const mtd_spi_nor_params_t _samd51_nor_params = {
+    .opcode = &mtd_spi_nor_opcode_default,
+    .wait_chip_erase = 15 * US_PER_SEC,
+    .wait_32k_erase = 150 * US_PER_MS,
+    .wait_64k_erase = 250 * US_PER_MS,
+    .wait_sector_erase = 50 * US_PER_MS,
+    .wait_chip_wake_up = 1 * US_PER_MS,
+    .clk  = MHZ(54),
+    .flag = SPI_NOR_F_SECT_4K
+          | SPI_NOR_F_SECT_32K
+          | SPI_NOR_F_SECT_64K,
+    .spi  = SPI_DEV(3),
+    .mode = SPI_MODE_0,
+    .cs   = SAM0_QSPI_PIN_CS,
+    .wp   = SAM0_QSPI_PIN_DATA_2,
+    .hold = SAM0_QSPI_PIN_DATA_3,
+};
+
+static mtd_spi_nor_t samd51_nor_dev = {
+    .base = {
+        .driver = &mtd_spi_nor_driver,
+        .page_size = 256,
+        .pages_per_sector = 16,
+    },
+    .params = &_samd51_nor_params,
+};
+
+mtd_dev_t *mtd0 = (mtd_dev_t *)&samd51_nor_dev;
+#endif /* MODULE_MTD */
+
+void board_init(void)
+{
+    if (IS_USED(MODULE_DAC_DDS)) {
+        gpio_init(SPEAKER_ENABLE_PIN, GPIO_OUT);
+        gpio_set(SPEAKER_ENABLE_PIN);
+    }
+
+    /* ST7735 driver is not supported yet uncomment the following code once it is */
+    /* if (IS_USED(MODULE_ST7735)) {
+        gpio_init(BACKLIGHT_PIN, GPIO_OUT);
+    }*/
+}

boards/adafruit-pybadge/doc.txt

@@ -0,0 +1,40 @@
+/**
+@defgroup    boards_adafruit-pybadge Adafruit PyBadge
+@ingroup     boards
+@brief       Support for the Adafruit PyBadge board.
+
+### General information
+
+The [Adafruit PyBadge](https://www.adafruit.com/product/4200) is a
+learning and development board that provides 5 Neopixel LEDs, an accelerometer,
+a light sensor, a speaker, several buttons and an LCD screen.
+It is powered by an Atmel SAMD51 microcontroller.
+
+The display, RGB LEDs, buttons and accelerometer of this board are currently not supported.
+
+The [Adafruit PyBadge LC](https://www.adafruit.com/product/3939) and
+[Adafruit EdgeBadge](https://www.adafruit.com/product/4400)) are
+variants of the Pybadge with small differences:
+- EdgeBadge provides an extra microphone (not supported)
+- PyBadgeLC only have one Neopixel LED (instead of 5)
+Both are compatible with the PyBadge RIOT port and the current port can easily
+be adapted/extended with their respective differences.
+
+### Flash the board
+
+Connect the board via USB and use `BOARD=adafruit-pybadge` with the `make` command;
+this uses the Arduino style bootloader preprogrammed on the board.<br/>
+Example with `hello-world` application:
+```
+     make BOARD=adafruit-pybadge -C examples/hello-world flash
+```
+
+In case of a crash of the firmware, one has to manually reset the board in
+bootloader mode to be able to re-flash it again: simply double tap the reset
+button before running the flash command provided above.
+
+### Accessing STDIO via UART
+
+STDIO of RIOT is directly available over the USB port.
+
+ */

boards/adafruit-pybadge/include/board.h

@@ -0,0 +1,116 @@
+/*
+ * Copyright (C) 2020 Inria
+ *
+ * This file is subject to the terms and conditions of the GNU Lesser
+ * General Public License v2.1. See the file LICENSE in the top level
+ * directory for more details.
+ */
+
+/**
+ * @ingroup     boards_adafruit-pybadge
+ * @{
+ *
+ * @file
+ * @brief       Board specific definitions for the Adafruit PyBadge
+ *
+ * @author      Alexandre Abadie <alexandre.abadie@inria.fr>
+ */
+
+#ifndef BOARD_H
+#define BOARD_H
+
+#include "cpu.h"
+#include "mtd.h"
+#include "periph/gpio.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/**
+ * @name    LED pin definitions and handlers
+ * @{
+ */
+#define LED0_PIN            GPIO_PIN(PA, 23)                    /**< LED0 pin */
+
+#define LED_PORT            PORT->Group[PA]                     /**< LED0 port */
+#define LED0_MASK           (1 << 23)                           /**< LED0 mask */
+
+#define LED0_ON             (LED_PORT.OUTSET.reg = LED0_MASK)   /**< LED0 on macro */
+#define LED0_OFF            (LED_PORT.OUTCLR.reg = LED0_MASK)   /**< LED0 off macro */
+#define LED0_TOGGLE         (LED_PORT.OUTTGL.reg = LED0_MASK)   /**< LED0 toggle macro */
+
+#define LED0_NAME           "LED(Red)"                          /**< LED0 name */
+/** @} */
+
+/**
+ * @name    Buttons control (TI SN74HC165 shift register)
+ * @{
+ */
+#define BUTTON_LATCH        GPIO_PIN(PB, 0)                     /**< Latch pin */
+#define BUTTON_CLK          GPIO_PIN(PB, 31)                    /**< Clock pin */
+#define BUTTON_OUT          GPIO_PIN(PB, 30)                    /**< Serial output pin */
+/** @} */
+
+/**
+ * @name    Backlight control
+ * @{
+ */
+#define BACKLIGHT_PIN          GPIO_PIN(PA, 1)                  /**< Backlight pin */
+#define BACKLIGHT_PORT         PORT->Group[PA]                  /**< Backlight pin port */
+#define BACKLIGHT_MASK         (1 << 1)                         /**< Backlight pin mask */
+#define BACKLIGHT_ON           (BACKLIGHT_PORT.OUTSET.reg = BACKLIGHT_MASK) /**< Turn backlight on */
+#define BACKLIGHT_OFF          (BACKLIGHT_PORT.OUTCLR.reg = BACKLIGHT_MASK) /**< Turn backlight off */
+/** @} */
+
+/**
+ * @name    Display configuration (not supported yet)
+ * @{
+ */
+#define ST7735_PARAM_SPI       SPI_DEV(1)                      /**< SPI device */
+#define ST7735_PARAM_CS        GPIO_PIN(PB, 7)                 /**< Chip select pin */
+#define ST7735_PARAM_DCX       GPIO_PIN(PB, 5)                 /**< DCX pin */
+#define ST7735_PARAM_RST       GPIO_PIN(PA, 0)                 /**< Reset pin */
+#define ST7735_PARAM_NUM_LINES (128U)                          /**< Number of screen lines */
+#define ST7735_PARAM_RGB       (1)                             /**< RGB configuration */
+#define ST7735_PARAM_INVERTED  (1)                             /**< Inversion configuration */
+/** @} */
+
+/**
+ * @name    Neopixel LEDs (not supported yet)
+ * @{
+ */
+#define WS281X_PARAM_PIN        (GPIO_PIN(PA, 15))              /**< GPIO pin connected to the data pin of the first LED */
+#define WS281X_PARAM_NUMOF      (5U)                            /**< Number of LEDs chained */
+/** @} */
+
+/**
+ * @name    Speaker (supported via DAC DDS module)
+ * @{
+ */
+#define SPEAKER_ENABLE_PIN      GPIO_PIN(PA, 27)                /**< Speaker enable pin */
+#define SPEAKER_PIN             GPIO_PIN(PA, 2)                 /**< Speaker pin (A0) */
+/** @} */
+
+/**
+ * @name MTD configuration
+ * @{
+ */
+extern mtd_dev_t *mtd0;                                         /**< pointer to mtd0 */
+#define MTD_0 mtd0                                              /**< mtd0 constant */
+/** @} */
+
+/**
+ * @name    Xtimer configuration
+ * @{
+ */
+#define XTIMER_WIDTH                (32)                        /**< Default timer is 32bit width */
+#define XTIMER_HZ                   (1000000ul)                 /**< Default timer runs at 1MHz */
+/** @} */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* BOARD_H */
+/** @} */

boards/adafruit-pybadge/include/gpio_params.h

@@ -0,0 +1,46 @@
+/*
+ * Copyright (C)  2020 Inria
+ *
+ * This file is subject to the terms and conditions of the GNU Lesser
+ * General Public License v2.1. See the file LICENSE in the top level
+ * directory for more details.
+ */
+
+/**
+ * @ingroup     boards_adafruit-pybadge
+ * @{
+ *
+ * @file
+ * @brief       Board specific configuration of direct mapped GPIOs
+ *
+ * @author      Alexandre Abadie <alexandre.abadie@inria.fr>
+ */
+
+#ifndef GPIO_PARAMS_H
+#define GPIO_PARAMS_H
+
+#include "board.h"
+#include "saul/periph.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/**
+ * @brief    GPIO pin configuration
+ */
+static const  saul_gpio_params_t saul_gpio_params[] =
+{
+    {
+        .name = LED0_NAME,
+        .pin = LED0_PIN,
+        .mode = GPIO_OUT
+    },
+};
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* GPIO_PARAMS_H */
+/** @} */

boards/adafruit-pybadge/include/periph_conf.h

@@ -0,0 +1,301 @@
+/*
+ * Copyright (C)  2020 Inria
+ *
+ * This file is subject to the terms and conditions of the GNU Lesser
+ * General Public License v2.1. See the file LICENSE in the top level
+ * directory for more details.
+ */
+
+/**
+ * @ingroup     boards_adafruit-pybadge
+ * @{
+ *
+ * @file
+ * @brief       Configuration of CPU peripherals for the Adafruit PyBadge
+ *
+ * @author      Alexandre Abadie <alexandre.abadie@inria.fr>
+ */
+
+#ifndef PERIPH_CONF_H
+#define PERIPH_CONF_H
+
+#include "periph_cpu.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/**
+ * @name    desired core clock frequency
+ * @{
+ */
+#ifndef CLOCK_CORECLOCK
+#define CLOCK_CORECLOCK     MHZ(120)
+#endif
+/** @} */
+
+/**
+ * @name    32kHz Oscillator configuration
+ * @{
+ */
+#define EXTERNAL_OSC32_SOURCE                    0
+#define ULTRA_LOW_POWER_INTERNAL_OSC_SOURCE      1
+/** @} */
+
+/**
+ * @brief Enable the internal DC/DC converter
+ *        The board is equipped with the necessary inductor.
+ */
+#define USE_VREG_BUCK       (1)
+
+/**
+ * @name Timer peripheral configuration
+ * @{
+ */
+static const tc32_conf_t timer_config[] = {
+    {   /* Timer 0 - System Clock */
+        .dev            = TC0,
+        .irq            = TC0_IRQn,
+        .mclk           = &MCLK->APBAMASK.reg,
+        .mclk_mask      = MCLK_APBAMASK_TC0 | MCLK_APBAMASK_TC1,
+        .gclk_id        = TC0_GCLK_ID,
+        .gclk_src       = SAM0_GCLK_TIMER,
+        .flags          = TC_CTRLA_MODE_COUNT32,
+    },
+    {   /* Timer 1 */
+        .dev            = TC2,
+        .irq            = TC2_IRQn,
+        .mclk           = &MCLK->APBBMASK.reg,
+        .mclk_mask      = MCLK_APBBMASK_TC2 | MCLK_APBBMASK_TC3,
+        .gclk_id        = TC2_GCLK_ID,
+        .gclk_src       = SAM0_GCLK_TIMER,
+        .flags          = TC_CTRLA_MODE_COUNT32,
+    }
+};
+
+/* Timer 0 configuration */
+#define TIMER_0_CHANNELS    2
+#define TIMER_0_ISR         isr_tc0
+
+/* Timer 1 configuration */
+#define TIMER_1_CHANNELS    2
+#define TIMER_1_ISR         isr_tc2
+
+#define TIMER_NUMOF         ARRAY_SIZE(timer_config)
+/** @} */
+
+/**
+ * @name UART configuration
+ * @{
+ */
+static const uart_conf_t uart_config[] = {
+    {    /* Virtual COM Port */
+        .dev      = &SERCOM5->USART,
+        .rx_pin   = GPIO_PIN(PB, 16),
+        .tx_pin   = GPIO_PIN(PB, 17),
+#ifdef MODULE_SAM0_PERIPH_UART_HW_FC
+        .rts_pin  = GPIO_UNDEF,
+        .cts_pin  = GPIO_UNDEF,
+#endif
+        .mux      = GPIO_MUX_C,
+        .rx_pad   = UART_PAD_RX_1,
+        .tx_pad   = UART_PAD_TX_0,
+        .flags    = UART_FLAG_NONE,
+        .gclk_src = SAM0_GCLK_PERIPH,
+    }
+};
+
+/* interrupt function name mapping */
+#define UART_0_ISR          isr_sercom5_2
+#define UART_0_ISR_TX       isr_sercom5_0
+
+#define UART_NUMOF          ARRAY_SIZE(uart_config)
+/** @} */
+
+/**
+ * @name PWM configuration
+ * @{
+ */
+#define PWM_0_EN            1
+
+#if PWM_0_EN
+/* PWM0 channels */
+static const pwm_conf_chan_t pwm_chan0_config[] = {
+    /* GPIO pin, MUX value, TCC channel */
+    { GPIO_PIN(PA, 22), GPIO_MUX_G, 2 },
+};
+#endif
+
+/* PWM device configuration */
+static const pwm_conf_t pwm_config[] = {
+#if PWM_0_EN
+    { .tim  = TCC_CONFIG(TCC0),
+      .chan = pwm_chan0_config,
+      .chan_numof = ARRAY_SIZE(pwm_chan0_config),
+      .gclk_src = SAM0_GCLK_PERIPH,
+    },
+#endif
+};
+
+/* number of devices that are actually defined */
+#define PWM_NUMOF           ARRAY_SIZE(pwm_config)
+/** @} */
+
+/**
+ * @name    SPI configuration
+ * @{
+ */
+static const spi_conf_t spi_config[] = {
+    {
+        .dev      = &(SERCOM1->SPI),
+        .miso_pin = GPIO_PIN(PB, 22),
+        .mosi_pin = GPIO_PIN(PB, 23),
+        .clk_pin  = GPIO_PIN(PA, 17),
+        .miso_mux = GPIO_MUX_C,
+        .mosi_mux = GPIO_MUX_C,
+        .clk_mux  = GPIO_MUX_C,
+        .miso_pad = SPI_PAD_MISO_2,
+        .mosi_pad = SPI_PAD_MOSI_3_SCK_1,
+        .gclk_src = SAM0_GCLK_PERIPH,
+#ifdef MODULE_PERIPH_DMA
+        .tx_trigger = SERCOM1_DMAC_ID_TX,
+        .rx_trigger = SERCOM1_DMAC_ID_RX,
+#endif
+    },
+    {   /* Connected to TFT display */
+        .dev      = &(SERCOM4->SPI),
+        .miso_pin = GPIO_PIN(PB, 12),
+        .mosi_pin = GPIO_PIN(PB, 15),
+        .clk_pin  = GPIO_PIN(PB, 13),
+        .miso_mux = GPIO_MUX_C,
+        .mosi_mux = GPIO_MUX_C,
+        .clk_mux  = GPIO_MUX_C,
+        .miso_pad = SPI_PAD_MISO_0,
+        .mosi_pad = SPI_PAD_MOSI_3_SCK_1,
+        .gclk_src = SAM0_GCLK_PERIPH,
+#ifdef MODULE_PERIPH_DMA
+        .tx_trigger = SERCOM4_DMAC_ID_TX,
+        .rx_trigger = SERCOM4_DMAC_ID_RX,
+#endif
+    },
+    {   /* Connected to PDM Mic */
+        .dev      = &(SERCOM3->SPI),
+        .miso_pin = GPIO_PIN(PA, 18),
+        .mosi_pin = GPIO_PIN(PA, 19),
+        .clk_pin  = GPIO_PIN(PA, 16),
+        .miso_mux = GPIO_MUX_D,
+        .mosi_mux = GPIO_MUX_D,
+        .clk_mux  = GPIO_MUX_D,
+        .miso_pad = SPI_PAD_MISO_2,
+        .mosi_pad = SPI_PAD_MOSI_3_SCK_1,
+        .gclk_src = SAM0_GCLK_PERIPH,
+#ifdef MODULE_PERIPH_DMA
+        .tx_trigger = SERCOM4_DMAC_ID_TX,
+        .rx_trigger = SERCOM4_DMAC_ID_RX,
+#endif
+    },
+#ifdef MODULE_PERIPH_SPI_ON_QSPI
+    {    /* QSPI in SPI mode */
+        .dev      = QSPI,
+        .miso_pin = SAM0_QSPI_PIN_DATA_1,
+        .mosi_pin = SAM0_QSPI_PIN_DATA_0,
+        .clk_pin  = SAM0_QSPI_PIN_CLK,
+        .miso_mux = SAM0_QSPI_MUX,
+        .mosi_mux = SAM0_QSPI_MUX,
+        .clk_mux  = SAM0_QSPI_MUX,
+        .miso_pad = SPI_PAD_MISO_0,         /* unused */
+        .mosi_pad = SPI_PAD_MOSI_0_SCK_1,   /* unused */
+        .gclk_src = SAM0_GCLK_MAIN,         /* unused */
+#ifdef MODULE_PERIPH_DMA
+        .tx_trigger = QSPI_DMAC_ID_TX,
+        .rx_trigger = QSPI_DMAC_ID_RX,
+#endif
+    },
+#endif
+};
+
+#define SPI_NUMOF           ARRAY_SIZE(spi_config)
+/** @} */
+
+/**
+ * @name I2C configuration
+ * @{
+ */
+static const i2c_conf_t i2c_config[] = {
+    {
+        .dev      = &(SERCOM2->I2CM),
+        .speed    = I2C_SPEED_NORMAL,
+        .scl_pin  = GPIO_PIN(PA, 13),
+        .sda_pin  = GPIO_PIN(PA, 12),
+        .mux      = GPIO_MUX_C,
+        .gclk_src = SAM0_GCLK_PERIPH,
+        .flags    = I2C_FLAG_NONE
+    },
+};
+#define I2C_NUMOF           ARRAY_SIZE(i2c_config)
+/** @} */
+
+/**,
+ * @name RTT configuration
+ * @{
+ */
+#ifndef RTT_FREQUENCY
+#define RTT_FREQUENCY       (32768U)
+#endif
+/** @} */
+
+/**
+ * @name USB peripheral configuration
+ * @{
+ */
+static const sam0_common_usb_config_t sam_usbdev_config[] = {
+    {
+        .dm     = GPIO_PIN(PA, 24),
+        .dp     = GPIO_PIN(PA, 25),
+        .d_mux  = GPIO_MUX_H,
+        .device = &USB->DEVICE,
+        .gclk_src = SAM0_GCLK_48MHZ,
+    }
+};
+/** @} */
+
+/**
+ * @name ADC Configuration
+ * @{
+ */
+
+/* ADC Default values */
+#define ADC_PRESCALER                       ADC_CTRLA_PRESCALER_DIV128
+
+#define ADC_NEG_INPUT                       ADC_INPUTCTRL_MUXNEG(0x18u)
+#define ADC_REF_DEFAULT                     ADC_REFCTRL_REFSEL_INTVCC1
+#define ADC_DEV                             ADC1
+
+static const adc_conf_chan_t adc_channels[] = {
+    /* port, pin, muxpos */
+    {GPIO_PIN(PB, 8), ADC_INPUTCTRL_MUXPOS(ADC_INPUTCTRL_MUXPOS_AIN2)}, /* A2 */
+    {GPIO_PIN(PB, 9), ADC_INPUTCTRL_MUXPOS(ADC_INPUTCTRL_MUXPOS_AIN3)}, /* A3 */
+    {GPIO_PIN(PB, 4), ADC_INPUTCTRL_MUXPOS(ADC_INPUTCTRL_MUXPOS_AIN6)}, /* A7 - Light sensor */
+};
+
+#define ADC_NUMOF                           ARRAY_SIZE(adc_channels)
+/** @} */
+
+/**
+ * @name DAC configuration
+ * @{
+ */
+#define DAC_CLOCK           SAM0_GCLK_TIMER         /**< Must not exceed 12 MHz */
+/** Use external reference voltage on PA03
+ *
+ * PA03 has to be manually connected to Vcc.
+ * Internal reference only gives 1V */
+#define DAC_VREF            DAC_CTRLB_REFSEL_VREFPU
+/** @} */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* PERIPH_CONF_H */
+/** @} */