RIOT/boards/msba2/Makefile.dep

ifneq (,$(filter netdev_default,$(USEMODULE)))
  USEMODULE += cc1100
  USEMODULE += cc110x_868mhz
endif

ifneq (,$(filter saul_default,$(USEMODULE)))
  USEMODULE += ltc4150
  USEMODULE += sht11
endif

# default to mtd_mci
ifneq (,$(filter mtd,$(USEMODULE)))
  USEMODULE += mtd_mci
endif

# default to using FAT on the SD card
ifneq (,$(filter vfs_default,$(USEMODULE)))
  USEMODULE += fatfs_vfs
  USEMODULE += mtd
endif
boards: remove duplicate gnrc_netdev_default from Makefile.dep `gnrc_netdev_default` will pull in `netdev_default`, so no need to check for both in `Makefile.dep` 2020-05-04 19:47:27 +02:00			`ifneq (,$(filter netdev_default,$(USEMODULE)))`
boards: Added cc110x params for MSB-A2 & MSB-IoT 2018-12-21 10:36:01 +01:00			`USEMODULE += cc1100`
boards: select 868 MHz band for CC110x 2021-09-16 18:47:44 +02:00			`USEMODULE += cc110x_868mhz`
boards: Added cc110x params for MSB-A2 & MSB-IoT 2018-12-21 10:36:01 +01:00			`endif`

drivers/sht1x: Major refactoring - Use RIOT's GPIO interface to access the sensor to increase portability - Changed API to allow more than one sensor per board - Added `sht1x_params.h` that specifies how the sensors is connected - each board can overwrite default settings by #defining SHT1X_PARAM_CLK and SHT1X_PARAM_DATA - Changed arithmetic to use integer calculations only instead of floating point arithmetic - Added support for checking the CRC sum - Allow optional skipping of the CRC check to speed up measuring - Added support for advanced features like reducing the resolution and skipping calibration to speed up measuring - Allow specifying the supply voltage of sensor which heavily influences the temperature result (and use that information to calculate the correct temperature) - Reset sensor on initialization to bring it in a well known state - Support for the obscure heater feature. (Can be useful to check the temperature sensor?) - Updated old SHT11 shell commands to the new driver interface, thus allowing more than one SHT10/11/15 sensor to be used - Added new shell command to allow full configuration of all attached SHT1x sensors - Removed old command for setting the SHT11 temperature offset, as this feature is implemented in the new configuration command 2018-06-13 09:17:29 +02:00			`ifneq (,$(filter saul_default,$(USEMODULE)))`
boards/msba2: Added ltc4150 to saul_default 2018-08-23 11:33:05 +02:00			`USEMODULE += ltc4150`
drivers/sht1x: Major refactoring - Use RIOT's GPIO interface to access the sensor to increase portability - Changed API to allow more than one sensor per board - Added `sht1x_params.h` that specifies how the sensors is connected - each board can overwrite default settings by #defining SHT1X_PARAM_CLK and SHT1X_PARAM_DATA - Changed arithmetic to use integer calculations only instead of floating point arithmetic - Added support for checking the CRC sum - Allow optional skipping of the CRC check to speed up measuring - Added support for advanced features like reducing the resolution and skipping calibration to speed up measuring - Allow specifying the supply voltage of sensor which heavily influences the temperature result (and use that information to calculate the correct temperature) - Reset sensor on initialization to bring it in a well known state - Support for the obscure heater feature. (Can be useful to check the temperature sensor?) - Updated old SHT11 shell commands to the new driver interface, thus allowing more than one SHT10/11/15 sensor to be used - Added new shell command to allow full configuration of all attached SHT1x sensors - Removed old command for setting the SHT11 temperature offset, as this feature is implemented in the new configuration command 2018-06-13 09:17:29 +02:00			`USEMODULE += sht11`
			`endif`
boards/msba2: add default MTD backend 2020-09-04 00:46:40 +02:00
boards/{mcb2388,msba2}: use mtd_mci as default MTD 2021-11-26 18:36:03 +01:00			`# default to mtd_mci`
boards/msba2: add default MTD backend 2020-09-04 00:46:40 +02:00			`ifneq (,$(filter mtd,$(USEMODULE)))`
boards/{mcb2388,msba2}: use mtd_mci as default MTD 2021-11-26 18:36:03 +01:00			`USEMODULE += mtd_mci`
boards/msba2: add default MTD backend 2020-09-04 00:46:40 +02:00			`endif`
boards/msba2: configure FAT on SD card 2022-02-14 14:31:31 +01:00
			`# default to using FAT on the SD card`
			`ifneq (,$(filter vfs_default,$(USEMODULE)))`
			`USEMODULE += fatfs_vfs`
			`USEMODULE += mtd`
			`endif`