mirror of
https://github.com/RIOT-OS/RIOT.git
synced 2024-12-29 04:50:03 +01:00
62 lines
2.1 KiB
Plaintext
62 lines
2.1 KiB
Plaintext
|
/**
|
||
|
|
@defgroup boards_wemos-zero WeMos Arduino Zero Clone
|
||
|
|
@ingroup boards
|
||
|
|
@brief Support for the WeMos Arduino Zero Clone board.
|
||
|
|
|
||
|
|
## Overview
|
||
|
|
|
||
|
|
The WeMos Zero is a cheap clone of Arduino Zero featuring a ATSAMD21G18A.
|
||
|
|
Unlike the original Zero, it does not include an embedded debugger/programmer.
|
||
|
|
Instead, the [UF2 Bootloader](https://github.com/microsoft/uf2-samdx1) is
|
||
|
|
used to program this board. The SAMD21 is a ARM Cortex-M0+ micro-controller.
|
||
|
|
It has 256KiB of flash memory and 32KiB of RAM.
|
||
|
|
|
||
|
|
Note: The official Arduino Zero using the native USB port and the Adafruit
|
||
|
|
Metro M0 Express should also work with board definition.
|
||
|
|
|
||
|
|
## Hardware
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
### MCU
|
||
|
|
| MCU | ATSAMD21G18A |
|
||
|
|
|:------------- |:------------------------------------- |
|
||
|
|
| Family | ARM Cortex-M0+ |
|
||
|
|
| Vendor | Atmel |
|
||
|
|
| RAM | 32KiB |
|
||
|
|
| Flash | 256KiB |
|
||
|
|
| Frequency | up to 48MHz |
|
||
|
|
| FPU | no |
|
||
|
|
| Timers | 6 (1x 16-bit, 2x 24-bit, 3x 32-bit) |
|
||
|
|
| ADCs | 6x 12-bit channels) |
|
||
|
|
| UARTs | 2 |
|
||
|
|
| SPIs | max 6 (see UART) |
|
||
|
|
| I2Cs | max 6 (see UART) |
|
||
|
|
| Vcc | 1.8V - 3.6V |
|
||
|
|
| Datasheet | [Datasheet](http://ww1.microchip.com/downloads/en/DeviceDoc/SAM_D21_DA1_Family_Data%20Sheet_DS40001882E.pdf) |
|
||
|
|
|
||
|
|
### User Interface
|
||
|
|
|
||
|
|
1 LED:
|
||
|
|
|
||
|
|
| Device | PIN |
|
||
|
|
|:------ |:---- |
|
||
|
|
| LED0 | PA17 |
|
||
|
|
|
||
|
|
|
||
|
|
## Flashing the device
|
||
|
|
|
||
|
|
Assuming the [UF2 Bootloader](https://github.com/microsoft/uf2-samdx1) is
|
||
|
|
installed, just run:
|
||
|
|
|
||
|
|
```
|
||
|
|
make BOARD=wemos-zero flash
|
||
|
|
```
|
||
|
|
|
||
|
|
Hint: You can you press the reset button twice to manually enter the bootloader.
|
||
|
|
This is helpful if the board has crashed (e.g. due to a failed assert() during
|
||
|
|
start up).
|
||
|
|
|
||
|
|
*/
|